02:23:13pm, Friday, April 19, 2024
|
4010 Shifter
|
Posts: 64 |
Does anyone make a Shifter for 4010 transmission with a 3 speed Mike Langan 402-910-6949 |
|
Re: 4010 Shifter
|
Keep me posted on this if you find anything Mike. |
|
Re: 4010 Shifter
|
Registered: 07/09/2008 Posts: 103 |
I just made my own....you looking for lever operated or cable? |
|
Re: 4010 Shifter
|
Registered: 07/06/2017 Posts: 20 |
Mike,
I would be interested in a simillar set up (lever) either on the cage or up through the floor. Can you keep me in the loop as well? Mike Gomulka 603-833-6773 |
|
Re: 4010 Shifter
|
Registered: 03/02/2011 Posts: 31 |
you can make your own very easily. i mounted two pillow blocks on the top of my transmission housing with a 3/4" shaft. In the middle of the shaft i welded a mount for the shifter handle. On the right side i welded an arm on it and attached an adjustable rod i made to go from the factory shifter arm to the arm i welded on the 3/4" shaft. I also used the top factory shifter arm because it was easier to adapt the adjustable rod too. I used low sitting pillow blocks so it was easier to build the deck plate over. Hope this helps some. |
|
Re: 4010 Shifter
|
Posts: 64 |
Thanks for the Idea
I am doing this on dads tractor moving it from the dash to the floor for easier access I can always copy what I have on mine but I thought it would be good to see what others are doing Thanks for the comments and I will share what I come up with Mike Langan 402-910-6949 |
|
Re: 4010 Shifter
|
Registered: 09/17/2008 Posts: 157 |
We just made a pivot off the base of the roll cage. Has the lever going up beside the seat, with a tab at the base where it pivots at 90 degree angle from the lever with a hole to fit the factory linkage down to the transmission, |
|
Re: 4010 Shifter
|
Registered: 12/03/2013 Posts: 74 |
Mike, I built my own and it pretty simple. Three speed GMS tranny in 4010 case that is shifted on bottom shaft. I used a shift arm from a 4030 transmission to throw arm out away from side transmission case. This would allow control rod to come straight up off shift arm to inside of cage where I used a flat iron/ clutch lever from an old 105 combine (Lever could be made out of aluminum). Lever pivots off back corner of cage. Shift control rod connects to lever about two thirds the distance from pivot point. Lever move straight up and down. I also fabricated a aluminum shift gate that positions flat iron lever in gates/slots so there is no question what gear it is in and if it is in gear! Gate also contains neutral start switch that lever actuates when in NEUTRAL. The other thing I had to do is make a stop for the 4030 shift arm or it would allow too much travel of arm/shift cam and park spring on shift cam would come out of place. Stop bracket was also used for more micro switches that controls back-up, Neutral and Park lights on back of tractor. It took a little tweaking to get it all in adjustment but once adjusted I have had no problems with shifting/function of transmission or NEUTRAL start/light signals. If you are in Eastern Iowa come take a look. Tractor pulls with ECI known as the Double 00 Buck. DW |
|
Re: 4010 Shifter
|
scott potter
|
don slama has them already made up. mine works well |
|
Re: 4010 Shifter
|
little help please
|
This would be a nice option......but I'm having trouble understanding how it works. Any chance you can snap a couple pics of what this thing looks like? I'm more of a visual person. If Slama has them, I would like to get hold of him, got conatct info? |
|
Re: 4010 Shifter
|
Registered: 10/11/2016 Posts: 10 |
I'm working on putting shift kits together right now for 4010/4020 with a 3 speed. It includes the arm on the shift shaft, the linkage and billet aluminum handle. I'll get some pics up soon. Thanks, Mark
Van Maanen Performance (712)470-5487 |
|
Re: 4010 Shifter
|
Registered: 10/11/2016 Posts: 10 |
I couldnt get the pictures to load on here but they are on my facebook page and website. Thanks, Mark
Van Maanen Performance (712) 470-5487 Facebook; Van Maanen Performance Website; vmppullingparts.com |
|
Re: 4010 Shifter
|
Registered: 07/06/2017 Posts: 20 |
Mark,
Saw your photos, product looks great. How tall are the supports that hold the cross shaft? Just curious if they'll fit under the floor pan and cage lip. Thanks again Mike |
Website Statistics
Global: Topics: 38,578, Posts: 229,609, Members: 3,319.
This forum: Topics: 37,058, Posts: 225,859.
Global: Topics: 38,578, Posts: 229,609, Members: 3,319.
This forum: Topics: 37,058, Posts: 225,859.
Our newest member BadHabit2
