What's the payout for the farm classes?
by
Big Block Deere
-
Forum
Call seal tech. A lot cheaper than REI.
by
Big Block Deere
-
Forum
We used one from a 6600 or 4400 combine on my dad's 6030. The stock drive cable works and it has a 0-3500 rpm range.
by
Big Block Deere
-
Forum
Ebay has them, here's the link.
by
Big Block Deere
-
Forum
Hey Keith come over to Westgate and buy one of the 5.9 P pump engines I have. Ray
by
Big Block Deere
-
Forum
Saw this on Facebook
by
Big Block Deere
-
Forum
Someone is putting the screws to you if your paying $10-$14 each for fire rings. The last sets I bought from Seal Tec were $3 or $4 each.
by
Big Block Deere
-
Forum
Seal Tec will make the rings but you'll have to have a machine shop cut grooves in the liners or in the head.
by
Big Block Deere
-
Forum
I've never had good luck drilling them out. That stream of fluid need to come strait out of the jet in order for it to hit the flat part of the tip and make a nice spray pattern. The ones I've drilled seemed to shoot off to the side kind of like peeing down your leg.
by
Big Block Deere
-
Forum
by
Big Block Deere
-
Forum
by
Big Block Deere
-
Forum
I seen a 466 block break when the pump stuck. The lifter was pushed out the side of the block.
by
Big Block Deere
-
Forum
Never seen it done. What are you looking for a lighter rearend or a 2 speed like a quad range would have?
by
Big Block Deere
-
Forum
The P7100 is identical to a P3000 externally from what I've seen. Post a picture of it or tell us what engine its bolted to.
by
Big Block Deere
-
Forum
Air filter? That's what caused mine to be low on power.
by
Big Block Deere
-
Forum
I've seen photos of the of the first design of 3010s & 4010s. They had V4 & V6 engines in them. I sure am glad that didn't go into production!
by
Big Block Deere
-
Forum
I'll second that Seal-tech comment. I ordered mine on a Monday and had them in my hands Thursday of the same week! That's service not seen in the pulling world!
by
Big Block Deere
-
Forum
I played along with the guy texting people about items for sale on here a couple weeks ago. I got him to send me a cashiers check and I have to admit it looks pretty good.
He instructed me to deposit the check and then wire his shipper the remaining balance so the item can be picked up. I figure I'll mess with him for a little bit. He did overnight the check to me so it had to cost him a
by
Big Block Deere
-
Forum
He's sending me a cashiers check for a Massey 95. I figured I'd play his game and make him do some work and waste his money mailing me a check.
Dateline did a story a few years ago about these scams. Most of them were traced back to overseas.
by
Big Block Deere
-
Forum
Floyd Isabell from PA. Here's the link to the pistons he sells.
by
Big Block Deere
-
Forum
Big block lifter bores in stock form are 1.125 inches. Vogel makes roller lifters to fit in the stock bore. They will also loan you the tool it takes to cut a half moon notch in the side of the lifter bore. I've also heard of others installing a bushing in the stock bore so a smaller diameter lifter from a different application can be used. I have Vogel's lifters in mine and am very hap
by
Big Block Deere
-
Forum
I don't think people that pay the money to get on the dyno and buy several sets of injectors are going to give that info away for free. I know I wouldn't.
by
Big Block Deere
-
Forum
I bought a tractor in Canada a while back. Best thing you could do is put an ad on www.yesterdaystractor.com under the Hauling Schedule. It won't be cheap but its a lot less trouble then trying to get it yourself.
by
Big Block Deere
-
Forum
Lots of good iron in the pits. The stands were a little bare to start but more people started coming in as the night progressed. I think if they could have it at the Farm Progress Show grounds instead of the fair grounds you would see a better crowd.
by
Big Block Deere
-
Forum
Longer rod will take a little side load off the cylinder wall when the crank is at a 90 angle.
by
Big Block Deere
-
Forum
What will the weight and pay out be for the 15mph classes?
by
Big Block Deere
-
Forum
Is your pressure gauge liquid filled? I always run the filter after the charge pump.
by
Big Block Deere
-
Forum
I ordered sealing rings on a Monday from Seal Tech and had them by Thursday of the same week.
by
Big Block Deere
-
Forum
What's the weather like over there?
by
Big Block Deere
-
Forum
I can make you a billet 4 inch with a velocity stack for $295 shipped. 319 404 5146
by
Big Block Deere
-
Forum