Page 2 of 4
Pages: 1234
Results 31 - 60 of 91
snyder! - 11 years ago
i had snyder build me one will not be disapointed!
by
kolekennemer
-
Forum
Isn't the firing order diff? I think
by
kolekennemer
-
Forum
DOES ANYONE MAKE A TRUCK MANIFOLD FLANGE FOR A DT360 TO TURN IT UP RIGHT FOR STRAIGHT UP AND DOWN, SO THE TURBO WONT SET OUTSIDE THE HOOD OR HAVE ONE THEY WANNA SELL?
by
kolekennemer
-
Forum
What's a John Deere p pump off of 8630 worth prolly needs rebuilt? I would assume 11mm plungers what's the model of thoes also
by
kolekennemer
-
Forum
WILL THE W6 OR W9 FIT INTO A 560? AND ARE THEY FASTER?
by
kolekennemer
-
Forum
I would like to put 4th in the 3rd gear ratio speed it up I'm looking for some cheaper ways other than constant mesh what out flipping the bottom shaft gears and the upper? I've heard that will help
by
kolekennemer
-
Forum
ARE THE RING AND PINION THE SAME ON THE 400 AND 450 FARMALL? ALSO IF CHANGING THE GEARS INTO A 560 FARMALL THE FOWARD GEARS 1-5 WILL THEY INTERCHANGE AND IF SO WILL IT SPEED UP THE TRANSMISSION? I KNOW THIS IS KINDA A LOADED QUESTION BUT WHAT IM WANTING TO DO IS SPPED UP QUITE A BIT WITHOUT HAVING TO GO TO CONSTANT MESH GEARS
560 IH STOCK REAR END
WANTING TO PUT 400/450 FARMALL RING AND PINI
by
kolekennemer
-
Forum
Will the 358 manifold fit a 360?
by
kolekennemer
-
Forum
Yea I'm yea I'm looking for 1
by
kolekennemer
-
Forum
Yes I'm looking and what about a combine with a d312?
by
kolekennemer
-
Forum
What about combines?
by
kolekennemer
-
Forum
Ok what Ag manifolds fit a dt360 I know there will not a turbo flange that's ok what tractors other than 886 and 766 tractors will fit thanks guys.
by
kolekennemer
-
Forum
whats a set worth if a person can find a set?
by
kolekennemer
-
Forum
What's a 460 utility ring and pinion worth are they harder to find? Will they speed up a row crop trans?
by
kolekennemer
-
Forum
Yep we had it at the mo state fair had a fuel issue was fighting it all summer just went back to a Apump and changed the turbo set up. Hopefully bigger gear change this winter and pump change
by
kolekennemer
-
Forum
I can walk you threw it 417-848-7554 we have done a dt360 in a 560
by
kolekennemer
-
Forum
Why does everyone want them what makes them so desirable?
by
kolekennemer
-
Forum
8630 not currently running tractor had a cab fire
by
kolekennemer
-
Forum
What's a John Deere 619 block, head crank complete all stock worth?
by
kolekennemer
-
Forum
Anyone?
by
kolekennemer
-
Forum
Could be 180 out?
by
kolekennemer
-
Forum
Will a exhaust manifold off of a "1206" fit a dt360 looking for a Ag manifold for dt360 want the turbo under the hood have a truck manifold
by
kolekennemer
-
Forum
Just Standard I'm wanting to make 3rd the new 4 speed it up around 20% looking for 20mph in 3rd at 3000rpm
by
kolekennemer
-
Forum
3000rpm and it's standard I think how can you tell?
by
kolekennemer
-
Forum
What would be a good set up for cm gears on a 560 wanting to pull in 3rd gear around 20mph 3000 rpm what tooth selection
by
kolekennemer
-
Forum
dt360 timing help please
pump a pump with cut delevery valves prolly around 280cc
hx35 turbo
what would be something to start kinda middle of the road with that, what degree?
by
kolekennemer
-
Forum
This tractor was started on the ground in gear without a neutral start switch the guy that did this is lucky to be alive wheelie bars stopped the tractor when it hit the foundation
by
kolekennemer
-
Forum
this can happen to any one! safety first one one was hurt but was one very close call!
by
kolekennemer
-
Forum
I bought mine off a guy named toolz here on pulloff will run about 150ish Just look him up
by
kolekennemer
-
Forum
I Can help ya call me 417-848-7554
by
kolekennemer
-
Forum
Page 2 of 4
Pages: 1234