Page 1 of 2
Pages: 12
Results 1 - 30 of 35
Is there anyone besides Wilwood that makes aluminum front hubs for the old Ford pickup type spindles? Didnt want to mess with redrilling the factory cast ones and the Wilwood ones have a bolt flange on the back to bolt a rotor to. I can make some from scratch, was just looking for something easier. Looking to use a 5 on 4.75" wheel. Thanks Jeff
by
Jeff A. Gravert
-
Forum
I can help with MM parts. 308-940-0255 Thanks Jeff
by
Jeff A. Gravert
-
Forum
I had the same thing from advertising some stuff on YT. The fellow was from Michigan but the check came with a NC address and the same kind of instructions. I took it in and talked to the Sheriff. He explained to me that it is not this transaction the scammers are focusing on. If you deposit the check, they get your bank information and start another thread of destruction with your checks and
by
Jeff A. Gravert
-
Forum
Explaining the names to my nine year old boy that I took out of school to go to Gordyville since he wanted to see "big" tractors was akward.....
by
Jeff A. Gravert
-
Forum
Carbon fiber hoods are fantastic. Is $8-10,000 in my budget, well, not even close....
by
Jeff A. Gravert
-
Forum
I know this has been on here before but I cant seem to find it. What size master cylinder have you guys had success with in conjunction with the 120-6818 four piston calipers? I was thinking 3/4" The input will be appreciated. Thanks Jeff
by
Jeff A. Gravert
-
Forum
I have a pair of 15.5 X 38 tires in Wakeman Ohio and would like to find them a ride to Gordyville. Light and easy to move. I would pay gas or beer money. Give me a call 308-940-0255 Thanks for the help. Jeff Gravert
by
Jeff A. Gravert
-
Forum
Hire Sven to do it so you can run the video camera!
by
Jeff A. Gravert
-
Forum
I have two 400 Cases here in Nebraska. One runs, the other would make a good donor. Both would be for sale. 308-940-0255. Thanks Jeff
by
Jeff A. Gravert
-
Forum
YES, March 21st and 22nd. 2014. I will ask about getting website updated. Jeff
by
Jeff A. Gravert
-
Forum
I have been slowly working on two 310 Waukesha engines. One gas and one diesel. These are both restoration engines and wont be used for pulling or performance. Everyone recommends good rod bolts. I called ARP today and the ten year old parts kid I talked to said 1.85" was the longest available. The stock bolts are 2" with room for a little extra lenght. What has been used or does anybody ha
by
Jeff A. Gravert
-
Forum
I have one that is all tore apart and in a crate that I advertised on here for $850. A local fellow called six times in a row to secure the purchase and a year later I am still waiting on him and his money. Good luck. I would think a runner should be $1000 to $1500. Jeff
by
Jeff A. Gravert
-
Forum
I only ever talked with Adam once and he was very helpful with the parts we were needing for a project. He was passionate about pulling and the entire sport. It is truly a shame that he has been taken away from his family. Thought and prayers to everyone involved. Jeff Gravert
by
Jeff A. Gravert
-
Forum
I am working on a late 24 valve 5.9 Cummins. I think it is a 2006 model year. It is the higher HP engine that has the factory made girdle assembly around the bottom of the block. The crankshaft is bad and neither the machine shop or the Cummins dealer can tell me if a 12 valve shaft will work or what the year parameters are. They say there are too many part numbers and variations. I dont wan
by
Jeff A. Gravert
-
Forum
This is a very sad situation to loose the life of such a young man. Thoughts and prayers to John and family.
Jeff A. Gravert
by
Jeff A. Gravert
-
Forum
I have a two 310 Waukesha's to put back together for non-pulling use. I thought it would be worthwhile to put in the ARP rod bolts for security. Does anybody have the part number for them. Thanks Jeff @ Gravert Restoration 308-940-0255
by
Jeff A. Gravert
-
Forum
6.125 by 7.5 is pretty big. How many RPMs? How much do you want to spend? 308-940-0255 Jeff
by
Jeff A. Gravert
-
Forum
Thanks for the information guys. I was researching using a set of those rods for a different application and could not find any consistency of what bearing was used. I did not realize they could be built off different platforms. The 2.370" will work perfect for where Im trying to put them. Thanks again. Jeff
by
Jeff A. Gravert
-
Forum
What bearing is used or what size are the rod journals in an 8.3 Arias/Fontana/Miner engine? Thanks Jeff
by
Jeff A. Gravert
-
Forum
There is not a rulebook to be had. I have been trying to get one for three monthes.
by
Jeff A. Gravert
-
Forum
Carl, I have one franklin spindle that we bored the center out too far by accident. It would work for a mock up. Let me know, I could ship it to you. Later Jeff
by
Jeff A. Gravert
-
Forum
What class or rpm are you trying to run??
by
Jeff A. Gravert
-
Forum
Factory parts? Factory assembly? A small bellhousing six cylinder with 800 goods in front of a 670 rear would be fun at 5000 on up.
by
Jeff A. Gravert
-
Forum
I have a pair of 12.4X24" tires and wheels in Germantown KY that I need delivered to Gordyville. No fluid, light, easy to handle. Paying freight or beer money. Thanks Jeff Gravert 308-940-0255
by
Jeff A. Gravert
-
Forum
5 Star General is owned and driven by Art Forrest of Sligo PA. He is a great guy and an asset to antique pulling.
by
Jeff A. Gravert
-
Forum
I have a 3/16" sheet of 6061 aluminum that is 5 feet wide and 14 feet long. I was going to have it cut and bent into two sets of wedge frame rails. I have never done anyting with it and would sell that material. It is hard to find in that size. 308-940-0255 Jeff Gravert Central City, NE
by
Jeff A. Gravert
-
Forum
3500 is kind of a challenge. 4500 is fairly easy and attainable. Jeff
by
Jeff A. Gravert
-
Forum
I need one pushrod and possibly a full set of rocker arms for a 1206 resto project. 308-940-0255 Thanks Jeff
by
Jeff A. Gravert
-
Forum
I have a 1655 chassis that would be for sale pretty reasonable. Jeff 308-940-0255 Central City, NE
by
Jeff A. Gravert
-
Forum
Interested in whole tractor also. 308-940-0255 Thanks Jeff
by
Jeff A. Gravert
-
Forum
Page 1 of 2
Pages: 12