Page 4 of 4
Pages: 1234
Results 91 - 117 of 117
Congrats Allen all the hard work pays off!!!
by
turbo
-
Forum
I have complete 4430 bell hsg to axles i would sell or do some trading. it is a quad range. 812-309-3255
by
turbo
-
Forum
Just connect top of hyd pump hole to to line going back to trans and eliminate oil cooler and resevoir, with a hose and your done.
by
turbo
-
Forum
Gary if you want to know why i left early was because i found out my son just got very sick at home. I left rifgt after i pulled. i talked to Celestine commitee about leaving right away. They told me to go ahead and leave. They had no problem with what happened with rpm box. I asked if they wanted to check me. You also know how to contact me, you know who i am!!!!!!
by
turbo
-
Forum
Gary if i stand corrected nobody said anthing about your sled this you better re read what was posted!!!!!!
by
turbo
-
Forum
Just wondering what happened to the other 2 posts on here last night, or did it get bad on here again.
by
turbo
-
Forum
I can't believe you have not pushed the thrust brg out out yet with that much pressure! I run a 5 disk and run stock pressure and holds d3and 4 easily. I do not re do the valve body. I do all the valve work externally with linkages and no problem. all you have to do is plug off pto port. any question call my cell 812 309 3255.
by
turbo
-
Forum
Get the back engine plate from a 9400 combine or 4050 with a 359 in it, or a plate from a 4030. but you will have to modify everything in front of it, frame rails and hyd pump mount.
by
turbo
-
Forum
Firestone only bridgestone blow for no reason.
by
turbo
-
Forum
call me tomorow or before 10-30 this evening, 812-309-3255 thanks jason.
by
turbo
-
Forum
Anybody know thanks.
by
turbo
-
Forum
Wanting to know the person that had single probe pyros for sale before. They were yellow, with a probe. thanks for the name or the number. Turbo.
by
turbo
-
Forum
People still hiding behind names again. Grow a set!!! Jason Wehr AKA Turbo!
by
turbo
-
Forum
Would the person that had s400 for sale a couple months ago in Illinois call me if you still have turbo thanks. Call me 812 309 3255
by
turbo
-
Forum
Looking on info about pull in shelbyville KY. Thanks.
by
turbo
-
Forum
What is the date, please.
by
turbo
-
Forum
Any body with results!!!!
by
turbo
-
Forum
Can you post results when possible. Thanks!!!!
by
turbo
-
Forum
I also seen one blow out the bottom of a stock f250 powerstroke at a pull in southern IN. a few years ago. It was because he was dumb enough to stay in WFO while the cluch slipped very badly and barely moving. Thats when flywheels and clutches fly the worst is when there is that much heat built up on cast it just explodes, even when running stock rpms. It could happen on the street too if you st
by
turbo
-
Forum
Don't want to push out thrust brg on crank either. That much pressure will do do that. A safe pressure is 200-205..
by
turbo
-
Forum
Re: Re: - 14 years ago
I also thought it was 470 cube limit!!!
by
turbo
-
Forum
That will work on older tractors with big steering valve under dash, but not with newer styles with feedback cyl in steering motor for valve block under hood. leave you number i will call you back, for more info thanks.
by
turbo
-
Forum
Your stock steering has a feed back cylinder in it. it has to all hooked up as stock or it will not work. option is to install closed centre steering pump in column and connect to cylinders on front axle. Have any questions ask more on here be glad to answer. Call JD dealer and they can also help you out also.
by
turbo
-
Forum
9500 hot farm was 466xpress, then mike robbins on red hot . 12000 was guterslaugh?? on 6030,
by
turbo
-
Forum
Nice to see the original river rat, by mastersons.
by
turbo
-
Forum
Yes it will fit on a 4020 head but will have maybe remove hyd valve under hood and route exhaust out rear of hood.
by
turbo
-
Forum
Wanting to know if any results from KY farmstock results, in glencoe?
by
turbo
-
Forum
Page 4 of 4
Pages: 1234