Page 2 of 3
Pages: 123
Results 31 - 60 of 62
I have a complete 870 rear end assembly with the platform,also have the front end with the radiator. No sheet metal though.
$1300.00 715-308-2163
by
rdl1953
-
Forum
Karl at Atlas Tractor 651-428-4563
by
rdl1953
-
Forum
I have a pump core,715-308-2163
by
rdl1953
-
Forum
What bolt pattern do you need? I have a set with Franklin Planetary pattern
715-308-2163
by
rdl1953
-
Forum
In the parts book the 4 speed and high low range look to be the same. The rear end parts are lighter, the differential is a 3 spider, the bull pinions dont have the extra bushing on them, the bull gears are narrower, the ring gear and pinion shaft are lighter. Hope this helps:}
by
rdl1953
-
Forum
Near as I can remember the only difference is that the 1030 has a larger rear pinion shaft bearing. I don't think anything else has changed
by
rdl1953
-
Forum
I bet he will put 6 Yamaha turbo snowmobile motors in it and pull in the mod class ????
by
rdl1953
-
Forum
Congratulations to the Red Thunder team for there win at Enderle!!!!!!!!!!
Congratulations to Jason Hootman on his win at Enderle!!!!!!!
Great work guys!! See ya next season!!!!
by
rdl1953
-
Forum
The results are there,just the wrong year is showing
by
rdl1953
-
Forum
Brad Penn 20-50 is what we have used for years
by
rdl1953
-
Forum
We change ours ever hook,cook it and add some fresh,been working good
by
rdl1953
-
Forum
The only way to clean up excessive smoke is to have more air,which either means extensive head and cam work or a turbo
by
rdl1953
-
Forum
I have a parts kit for this.call me at 715-308-2163
by
rdl1953
-
Forum
That would be me,715-308-2163 $400.00 for a set of six
by
rdl1953
-
Forum
The valves will hit the sleeves unless you notch the sleeves
by
rdl1953
-
Forum
Call Lemke's They have a longer lifter that works well,you will need some block work to make any of them fit
by
rdl1953
-
Forum
Our light super stock will use 6 gallons plus
by
rdl1953
-
Forum
Be sure to have a steel flywheel and pressure plate before you plan to make any power,lawsuits are very expesive,
as far as power,the sky and check book is the limit,hope it runs good for you,not to many Case guys out there!
by
rdl1953
-
Forum
Yes,he texted me about a turbo,he needed way to much info so I stopped replying
by
rdl1953
-
Forum
I have take off 427 heads,$250.00,Im in nortwestern Wisc,715-308-21653
by
rdl1953
-
Forum
We did it some years back,not easy but can be done,715-308-2163
by
rdl1953
-
Forum
I had one done at Baxter Engines in Eau Claire Wisc,715-874-4142,it was several years ago and I had the weights cut out for them.Cost back then was $700.00 or so.Most engine shops can do this,Genes Machine,Riverside engines and I'm sure there are others.
by
rdl1953
-
Forum
Yes have bought there before,most times it was a good buy,some of the stuff is JUNK and people that buy a lot on there are close enough to the site to look at the items,I would guess that the high priced items were in good condition and that they had a high bid already placed,hope this helps.
by
rdl1953
-
Forum
Atlas tractor or Karl kaun
by
rdl1953
-
Forum
Service book shows them both at 16.5 to 1
by
rdl1953
-
Forum
You will need to get some higher compression pistons such as a 870 as your ratio is about 15.8 to1 with the turbo engine and a N.A. piston is 16.5 to 1,might be hard to get much over 150 HP
by
rdl1953
-
Forum
Had a DT core one time that was set up to run on CNG it had the diesel head with a spark plug adapter in place of the injector tube and a big bowl cut out of the piston,never did have it running and there was no ignition system on it,as far as a factory gas head I doubt there ever was one.
by
rdl1953
-
Forum
Region 3 tractor pull's Saturday and Sunday night at Ridgeland,Lots of tractors,Cold beer and good food,come early for good parking and seats
by
rdl1953
-
Forum
Mine come out on the side and are two rectagular holes with 4 bolts holding each upright exaust pipe on
by
rdl1953
-
Forum
Are you looking for one with two exaust outlets on the side? If so call me at 715-308-2163,Roger
by
rdl1953
-
Forum
Page 2 of 3
Pages: 123