Page 2 of 3
Pages: 123
Results 31 - 60 of 71
where did you have done originally? how many hooks on them? big or small pin and are you just changing set ups?
thansk again
by
Buckeyecrewcab
-
Forum
where do you guys send your connecting rods to be hardened? needing a set done for a small block deere...
thanks in advance for your replies
by
Buckeyecrewcab
-
Forum
Are there any updates on Jace and his hospital stay? I hope to find him in good health...
by
Buckeyecrewcab
-
Forum
I sell 3-6 inch guillotines. Also sell boost hoses, cables, velocity stacks, etc. Have everything in stock. Have quick shipping via ups. Id be happy to send pictures to you. 513-571-4532 thanks
by
Buckeyecrewcab
-
Forum
I bought my head gasket and fire rings as a set from riverside. Call and talk to phil. Has everything in stock
by
Buckeyecrewcab
-
Forum
Yanmar55, did you have the charger inlet towards the front of tractor with the 1'' spacer? and any problem with inlet piping lining up with intake? im running a center feed 55 series intake. i understand ill be making all new crossover but just seeing if there were any tricks. thanks again
by
Buckeyecrewcab
-
Forum
putting a 7810 exhaust manifold on a deere 466 motor to turn charger around for better air intake. Motor is in a deere 4430 with GT42 charger with 115 exhaust housing. Question is what kind of spacer/wedge have any of you guys had to use to make charger fit without rubbing the hood? Havent taken apart yet just trying to get everything gathered up for the project. Thanks in advance
by
Buckeyecrewcab
-
Forum
im running an aeromotive electric pump currently. switching to mechanical soon. it pushes enough fuel to support a 950cc pump. has 10 runs on it and for sale if interested. 513-571-4532
by
Buckeyecrewcab
-
Forum
Ive seen some guys that use john deere combine rear axle hubs. theyre 6 lug. others use trailer hubs that are 5 lug. hope this helps
by
Buckeyecrewcab
-
Forum
I sell 3'' guillotine shutoffs. Have guillotines, boost hoses, etc on shelf at all times. I can either do a 3'' or do a 3''x4'' adapter hose and get you alittle more air volume with a 4'' shutoff. Have sold alot off this setup for different turbos. The guillotine and adapter hose set up would run you $105 shipped. thanks 513-571-4532
by
Buckeyecrewcab
-
Forum
CDS offers both tuthill and scherzinger brand supply pumps. these drive off the front of the inj pump via a lovejoy coupler. it replaces the front timing cover. ive seen a lot of these style on tractors. I have the scherzinger style pumps for sale if interested
by
Buckeyecrewcab
-
Forum
Riverside(REI) has the items youre looking for. his number is in builders section. The heavy hold downs you just use 3 stock cast ones and ditch the 2 aluminum ones.
by
Buckeyecrewcab
-
Forum
3020 casting numbers r33450 weighs 266 lbs. for special offset r48954 weighs 530 lbs. deere shipping weights no crating. 720 center weights are posted above also
by
Buckeyecrewcab
-
Forum
f1500r weight is 266 lbs. f1478r weight is 252 lbs. thats coming straight from deere parts shipping weights. no crating
by
Buckeyecrewcab
-
Forum
I appreciate all the responses. thanks a bunch
by
Buckeyecrewcab
-
Forum
Anyone know the actual legal height that the indoor smoke tube exhaust pipe needs to be from ground to bottom of pipe? Also how far back past tractor must it extend. Cant seem to locate that info anywhere. thanks in advance
by
Buckeyecrewcab
-
Forum
you should check your local rules. alot of limited cube classes allow +/- 1%. so the 404 would able to run in that class. and yes the 404 is more tunable especially with more off the shelf parts available compared to the 359.
by
Buckeyecrewcab
-
Forum
Phil at riverside is very knowledgeable. He will tell you what you need to or don't need to do. Has fast turn around and great product. Had sleeves cut, running his rings and cam. everything works great
by
Buckeyecrewcab
-
Forum
4440 puller, did the setup from Bryce work well? how good are the calipers? And will wildwood calipers hold up under a tractor running 18.4x38 in a 9000 lb class? thanks just seeing if spending the extra money for billet calipers are worth it. thanks for any reply
by
Buckeyecrewcab
-
Forum
nick do u have a picture handy of your disc brake set up? are the calipers billet or wildwood, etc? getting ready to put a set on an altered farm
by
Buckeyecrewcab
-
Forum
you need a Viton o ring for that application to hold up to brake fluid. Mcmaster Carr has them same size as your originals. youll need the measurement of your stock o ring. use a new set of stock backup washers for the o rings from John Deere
by
Buckeyecrewcab
-
Forum
I bought a set of aluminum fenders for my 4430 from haslag steel. really nice fenders. tough brackets underneath also. gave $750 for them.
by
Buckeyecrewcab
-
Forum
greg lamb has an open station on the for sale page. nice sets are hard to find. last set I had I got $2200 out of
by
Buckeyecrewcab
-
Forum
what kind of machine work does it take to switch from 4430 axle housings to 4010 or 4020 housings? do I need to use the 4430 brake components or 4010/4020 components? and does anyone know the percentages gained on speed with the earlier housings? thanks
by
Buckeyecrewcab
-
Forum
who makes the best sbjd 3 speed for the best price. I understand none of them are cheap but wanna get a good product for good money. thank ya
by
Buckeyecrewcab
-
Forum
installed wildwood brake master cylinders on a sbjd 4430. all factory hyd pump,etc has been deleted. having trouble bleeding system. have masters installed in deere factory position with 3/16 lines adapted to fit factory internal brakes. tried DOT4 fluid and leaked past O-rings so put in aw SAE30 hyd fluid in. brakes will prime up hard as a rock. 10 minutes later theyre spongy again. I haven'
by
Buckeyecrewcab
-
Forum
u could always sell it and buy a green 1... ha
by
Buckeyecrewcab
-
Forum
have a 950cc CDS A pump. Going to be on a 3000 rpm sbjd. Im going to run a 10AN line from filter to injection pump with a T, but question is what size fuel lines do I need to run after the T? will 6an work or do I need 8an? thanks
by
Buckeyecrewcab
-
Forum
everyone told me to use the 55 series aluminum intake. midway through build, so im not sure on dyno numbers, etc. hope this helps
by
Buckeyecrewcab
-
Forum
try dengler tractor in ohio 513-423-4000 my buddy gets his ih parts from them
by
Buckeyecrewcab
-
Forum
Page 2 of 3
Pages: 123