Page 1 of 1 Pages: 1
Results 1 - 11 of 11
Looking for a tube frame or front clip for a 66 series. I’m located in Middle TN you can call or text 615/388-5460 thanks
by
806guy
-
Wanted
I was just wondering if anyone makes a quick release shaft and wheel for a factory IH steering column an still use the factory steering motor? Or what are you guys using, I’m going to a roll cage and need to change it to make room to get in, thanks.
by
806guy
-
Forum
Would it be laggy? I’ve seen s300s on them around here but running 13mms and injectors too, It’s not a hot rod or anything I’m just looking for something to move a little more air I’m guessing it’s around 300hp, but I’ll probably end up putting a good m100 back on it, I would like a 11mm but probably have to settle with a 10 that’s maxed, I don’t want to build a full blown puller out of it I alre
by
806guy
-
Forum
I’ve got a 1066 with a dt468 engine. It has the mw Bosch inline pump on it which I will probably pull off an put a model100 back on sometime. It’s turned up some and is very stout and I wanna put a better than stock turbo on it, I’ve got a couple of 3lm466s on some tractors I farm with and have had one on a puller and I think they’re a great turbo and not opposed to putting one on this one either
by
806guy
-
Forum
That’s what Jeff told us about the lifters today and that s what happened. The lifters I have wasn’t chamfered and that’s what it done.. It suck’s it’s junked the cam over it but now I know. I just put a head from Jeff on last week so hopefully it should all work together just fine now after it’s all back together .
by
806guy
-
Forum
Hey guys I’m running a 3200 rpm 466 ih. Just put a new suits cam in back in the spring degreed it in and have maybe 8-10 passes on it and I believe it’s already wore a couple of lobes prematurely, I haven’t pulled it out yet but have checked rockers an have 2 that’s open enough to slide a pencil in between the valves an arms. It’s not a valve setting problem because now you can’t even adjust the
by
806guy
-
Forum
Just curious on if anyone is running a Apex on a 466 ih 3000 rpm class and how well it does over anything else or worse. I’ve got one with a .98 exh housing I’m gonna try. I took off a FVP gt42 with a billet wheel with a 1.01 housing. Just wondering what your guys opinions an experience with one is. I’m running a FVP P3000, suits cam, water injection, haven’t had a chance to try it yet but for th
by
806guy
-
Forum
I’m not sure of the brand, it’s a steel flywheel that looks just like a cast one. The pads an pp say hy capacity
by
806guy
-
Forum
That’s what I thought when I first started it but the guy told me which way they go so that’s how I put it in but I’ll tear it back down an turn it around. I didn’t think the pate was supposed to rattle either but it does pretty bad
by
806guy
-
Forum
I put the spacers in it that came with it and he said everything was working good in his tractor, the front disk has to face the floater cause if turned around the hub hits the flywheel bolts, I’ve heard different ppl say they face different ways but it sounds like I may have to split it again to find out
by
806guy
-
Forum
I’ve put a dual disk in my 1066 and i can’t get it to engage or disengage correctly, I cut 1/4 in off the ipto shaft an throwout bearing housing so I could get the tractor bolted back together because it would not bolt all the way up until I done that, I bought the clutch used an the pp has spacers which move everything back further so now my clutch shaft that goes through the bellhousing the hoo
by
806guy
-
Forum