Page 3 of 5
Pages: 12345
Results 61 - 90 of 134
dt 466, water injection ,p-pump , open rpm, 3x4 turbo, limited pro set up
by
mid-west puller
-
Forum
how much piston skirt clearance is needed on a IH 466 dry engine????? thanks
by
mid-west puller
-
Forum
does anyone make a alluninum hub to fit factory ih spindal
by
mid-west puller
-
Forum
I think if you run the rules like Klint Tucker does for gordyville, you will find plenty of tractors.There is no real difference in 20.8 or 24-32s, in gordyville they all run together, tire size is'nt what puts you in the sand, its whats under the hood.
by
mid-west puller
-
Forum
I'd bring a 466 3x3,3x4 pro farm , limited pro from sd
by
mid-west puller
-
Forum
anbody can put 466 motor in and go pulling, pulling with a 361, or 407 shows PRIDE, and is priceless
by
mid-west puller
-
Forum
Say floyd, doe you have any pictures of this shifter setup, might be inerested also/// thanks
by
mid-west puller
-
Forum
great plains is haveing a pull in madison sd, at historic prairie village. 8-25-2012 raised purse for the super farm class, most likly wont be more than one true super farm there, the rest will be 466cu with 3x3 turbos. a lot of tractors in south west mn, western ia, and northeast neb, would fit in this class, all are welcome if interested call 605-480-1077
by
mid-west puller
-
Forum
so, is there abetter bolt pattern to use when mounting alluninum wheels on a stock IH 6 bolt hub??????????? thanks
by
mid-west puller
-
Forum
I dont do facebook so I would'nt know, but thanks again
by
mid-west puller
-
Forum
does anyone have # for cris pfeifer, the number I've been trying just goes to a voice mail, with no return call. I'm thinking maybe its not his ???? thanks
by
mid-west puller
-
Forum
who is the best head man in around tennesse???
by
mid-west puller
-
Forum
what classes did they run friday nite?????? Which ones will run on saterday?????????????
by
mid-west puller
-
Forum
I beleave there web site says there is no performance differance between the gtx and the gt42 , but a durability advantage, also remember the gtx is a ball bearing center, are you comparing to a journal bearing center? this may be the differance , ball bearing centers are supposed to spool up faster
by
mid-west puller
-
Forum
well, I called ace today, and theyDO NOT make a hub to fit stock IH front spindle
by
mid-west puller
-
Forum
does anyone make a aluminum hub to fit a factory IH front spindle ???????
by
mid-west puller
-
Forum
I just use 15-40 from john deere, I figured if it was good enough for 300,000 doller combine or tractor it was good enough for my pullers, but I always change oil about every six pulls, mostly because of wash, or fuel in the oil. two tractors, 14 years on the bearings between them
by
mid-west puller
-
Forum
Is there anyone out there that makes aluminum hubs for a Ih front end ???? thanks
by
mid-west puller
-
Forum
I don't remember the year but I remember they invited the open farm tractors to pull with them there. I could'nt go cause mine was down, I really regretted that. I really felt I missed out on something
by
mid-west puller
-
Forum
do you have a part number?????? thanks
by
mid-west puller
-
Forum
so what about this helm pump? where can it be found??????
by
mid-west puller
-
Forum
the rules meeting for 2012 was held last fall, but maybe the best thing to do is build your tractor the way you want, then start your own oginization, outlawing all IHs and john deeres and go pull on your own. that will really teach them
by
mid-west puller
-
Forum
they are not set yet
by
mid-west puller
-
Forum
where can the marine pump be found, and i,m assuming the old ih combine part you refered to is the steering cylinder??? thanks
by
mid-west puller
-
Forum
the rules allow the 504 case, BUT it must be in a tractor that it belongs in with the stock rear for that motor, for example you cannot run the 504 in a 930, but you can run it in the 1270, 1370, 1570, 2290 etc.the open farm is a 466 class, all engines large than 466 have to be in stock chassie 5020s with 531, 6030s with 619 and so on.
by
mid-west puller
-
Forum
what are you wanting to run? what class and trctor??
by
mid-west puller
-
Forum
so what do we know about this tractor deere addiction? think he was to be from wis. looked like he done REALLY well in gordyville, whos work is he running???
by
mid-west puller
-
Forum
so who all are building for the new class,,,, and what are the rules?????????????????????
by
mid-west puller
-
Forum
where is the best place to get disc brakes for a IH
by
mid-west puller
-
Forum
I make one out of stainless steel, 5 inch, very strong 250 plus shipping on hand post back if interested
by
mid-west puller
-
Forum
Page 3 of 5
Pages: 12345