Page 2 of 3
Pages: 123
Results 31 - 60 of 71
What is involved in putting a 4250 differential carrier in a 4010 or 4020?
by
mefarms68
-
Forum
Does anybody build a front piece for a 4430 that takes the place of the tank?
by
mefarms68
-
Forum
Can you put a 9.5L tire on a 10in rim?
by
mefarms68
-
Forum
Does anyone build a front piece for a 30 series deere that replaces the diesel tank?
by
mefarms68
-
Forum
What weight rating on front hubs do most run on a 8000 to 10,000 lb pro stock type of tractor?
by
mefarms68
-
Forum
Does anyone know the weight difference between the light and heavy 4010 housings and the 4020 housing?
by
mefarms68
-
Forum
Can you run hydraulic oil in the wildwood masters?
by
mefarms68
-
Forum
Do you use wilwood masters and dot brake fluid with the factory deer internals?
by
mefarms68
-
Forum
Does anyone run internal brakes on a sbjd?
by
mefarms68
-
Forum
What stock 4020 transmission parts can be used with most three speed setups?
by
mefarms68
-
Forum
The heavy 4010 housing.
by
mefarms68
-
Forum
Does anyone know the weight difference between the late 4010 housing and the 4020 housing?
by
mefarms68
-
Forum
What are the main advantages of an air suspension front end?
by
mefarms68
-
Forum
Looking to build a pro field 4010 and looking for advice on what I can do to upgrade the rearend and transmission a little at a time and eventually end up with a super farm over a couple of years.
by
mefarms68
-
Forum
9000 to 9500
by
mefarms68
-
Forum
Gears - 6 years ago
Looking for advice on gearing in a 4010. 466, 3x3, 24.5 tires, unlimited rpm.
by
mefarms68
-
Forum
P pump - 6 years ago
How much cost is involved in machining a sbjd a pump block for a p pump?
by
mefarms68
-
Forum
9000 lb hot farm/light limited prostock. 466, 3x3 turbo, p pump, unlimited rpm.
by
mefarms68
-
Forum
What are the advantages and disadvantages of a tube frame vs a channel frame other than weight?
by
mefarms68
-
Forum
Building an unlimited rpm sbjd 466 with a 13mm p pump. Already have a 3in. 7 blade precision charger. Wondering if I will be able spin it, or should I go to a six blade?
by
mefarms68
-
Forum
Has anyone used gears from Smiths performance in Holland NY. for transmission parts?
by
mefarms68
-
Forum
Where did you get your gears? I'm looking for something for a 4010.
by
mefarms68
-
Forum
Going to build a 466 in. Sbjd. 13 mm p pump, 3x3 turbo, unlimited rpms. Was wondering what the advantages were with a decubed 8.1 was over a 7.6, or older 466. Also considering a set up using 4.25in pistons with an offset ground 9 liter crank. Just looking for some advice.
by
mefarms68
-
Forum
Has anyone received a pro pulling mag lately? The last one I got was the February March issue.
by
mefarms68
-
Forum
What prefix in the engine serial number designates whether or not a block is a p pump or a pump block?
by
mefarms68
-
Forum
What is the going rate to needle a 4010 rear end and axels, and weld plates on?
by
mefarms68
-
Forum
Thinking about hardblocking the head on a jd 466. Open rpms, 3x3 turbo, wate injection. Wondering what the pros and cons are.
by
mefarms68
-
Forum
What's the part or casting number for the light weight housings?
by
mefarms68
-
Forum
Anybody running 4230 finals on a 4010? Advantages and disadvantages.
by
mefarms68
-
Forum
Has anyone got a pro pulling magazine lately?
by
mefarms68
-
Forum
Page 2 of 3
Pages: 123