10:19:15am, Sunday, May 19, 2024
Timing on a 1066 13mm?
|
looking for advice
|
Working on a 1066 with 414, 3lm 466 turbo, and model 100 13mm pump. looking for ideas of timing change from stock settings(I believe stock is 20?) . Pump does have advance in it. Pulling in 3000rpm classes. Thanks |
Re: Timing on a 1066 13mm?
|
denmark
|
I have same set up depends on fuel ,, stock is 18 I am runing 26-28 other guys are runing 24 i also herd people runing over 35 . I hade best luck around 26-28 . |
Re: Timing on a 1066 13mm?
|
Registered: 04/30/2008 Posts: 174 |
your best bet will be to start at about 22. that seems to be a nice place to start and many engines run great there,,,,,since ur not going for high rpms,,,and the rpm,s arent much more than stock,,,,u dont need a lot of advance...it should run fine at 22..23...the factory advance is 14 degrees on most of those pumps,,, |
Re: Timing on a 1066 13mm?
|
Anonymous User
|
i had a 13mm pump ambac, 35 degrees is great, adds another grear almost!
18 is stock by the book, i had to much flame at less than 35. |
Re: Timing on a 1066 13mm?
|
ice man
|
If you had to put your timing at 35 to keep the flame down you may need a new cam or one with a different grind. We run a 13 mil and a 15 mil and both are at 24 and we pull 3rd and 4th gear..... |
Re: Timing on a 1066 13mm?
|
Anonymous User
|
yes had a stock cam but had steel head gasket |
Re: Timing on a 1066 13mm?
|
Registered: 04/13/2008 Posts: 41 |
hey ice man were you running water? |
Re: Timing on a 1066 13mm?
|
Icemans
|
No |
Re: Timing on a 1066 13mm?
|
I started out at 20 with my pump and turned the manifold cherry red. Bumped it to 28 and till had 14 inch flame. Did some checking found out my pump has no advance, moved a tooth and ran at 33 with still 8 iches of flame. Moved it to 36 and have got the flame to around 5 inches. Going to move to 38 and see what happens. But if your pump has advance that is around 14 degrees, so pull 14 off my 36 and your at 22. Only two ways to put out a flame on a motor without water and that is more timing or more fuel. |
Re: Timing on a 1066 13mm?
|
Anonymous User
|
I AGREE, 22 IS WHERE MINE WAS AT, RAN GREAT |
Re: Timing on a 1066 13mm?
|
IH forever
|
I ran mine at 36 degrees and could run road gear on a hard track, 3rd on a tight track. 14 degrees in pump. |
Re: Timing on a 1066 13mm?
|
Registered: 04/13/2008 Posts: 41 |
what weight class are you running? |
Re: Timing on a 1066 13mm?
|
Anonymous User
|
How do you adjust the timing? |
Re: Timing on a 1066 13mm?
|
.02
|
you need a service manual for your make and model. |
Re: Timing on a 1066 13mm?
|
Anonymous User
|
what service manual would you recommend for an IH 1066 non-hydro? |
Website Statistics
Global: Topics: 38,779, Posts: 229,957, Members: 3,338.
This forum: Topics: 37,098, Posts: 226,040.
Global: Topics: 38,779, Posts: 229,957, Members: 3,338.
This forum: Topics: 37,098, Posts: 226,040.
Our newest member Jacklovik2009