BOSCH INJECTION PUMP July 11, 2010 06:18AM
HOW DO I FIND OUT WHAT IT IS
Reply Quote

Re: BOSCH INJECTION PUMP July 11, 2010 08:20AM
Both the injection pump and governor have their own identification tags.
The Bosch numbers provide a variety of information.
Looking at a typical U 900 with a 353.902 motor you will find:

Injection nozzles: DLLA 150 S 187
Nozzle holders: KDAL 74 S
Injection pump: PES 6 A 80 C 410 RS 2085 X
Governor: RSV 350...1300 A 2 B 1052D
What do these numbers mean?


Injection nozzles: DL = A hole type nozzle, one that sprays fuel through several holes in the tip of the nozzle body L = Indicates a "long" nozzle A = A code indicating details of nozzle design (4 hole, 5 hole, etc..) 150 = Spray pattern in degrees, 150° S = Nozzle shoulder diameter code. It must match the shoulder diameter of the nozzle holder. The sizes are: P = 14mm, R = 16mm, S = 17mm, T = 22mm, U = 30mm, V = 42mm, W = 50mm 187 = Application information code for Bosch use

Nozzle Holder: KD = All MB 300 series diesel motors use the KD style holder. This is identified by having a separate pressure screw (gland nut). The important designation is the letter code after the numeric identifier. In this case “S”. It must match the shoulder diameter code of actual nozzle.

Injection pump:
PE = An inline injection pump with integral camshaft S = With flange type mounting. (base or cradle mount pumps are identified as PE only) 6 = Number of high pressure outlets A = Pump size. Indicates an "A" size pump. As used by Bosch the term "size" is less indicative of actual size, than design characteristics. The word “model” is probably more accurate. 352/353 engines all have “A” series pumps. Early 366 motors will also have this pump, it was subsequently replaced by the heavier “MW” series pump. The larger 355 motors used with some rear engined snow blower systems use the "P" series pump. 80 = Plunger diameter in tenths of a mm. i.e. an 8.0 mm plunger C = Design change code, in this case the third design. A= 1, B= 2, C= 3, D= 4, etc.. 410 = Construction information; location of fuel transfer (feed) pump and governor. R = Direction of rotation when facing the drive end of the pump. R = right hand (clockwise) rotation. L = left hand (counter clockwise) rotation. S 2085 X = Bosch code for application and usage of the pump

Governor:
RS = Governor type (RS = tractor type, RQ = vehicular type V = Variable (all speed) governing. 350 = Low idle pump speed. (one half engine speed, or 700 rpm idle) ... = An additional designator for variable speed governing. A / (slash) in this position indicates minimum and maximum governing only. 1300 = Full load, rated speed. Pump rpm at maximum engine speed under full load. (one half of engine speed, or 2600 rpm ) A = The injection pump "size" this governor is intended for use with 2 B = Design change code. B = second version 1005 D = Bosch code for application and usage of governor
Reply Quote

Re: BOSCH INJECTION PUMP RSV350 February 03, 2012 06:51AM
we are looking for a mico bosch RSV350 1150A5C1277R injector pump would you by chance know where we can buy it.
thanks

betty mazac
parts and warranty administrator
979-885-3554--ext 25
979-885-0800--fax
Reply Quote

Re: BOSCH INJECTION PUMP April 19, 2018 06:27AM
I have a rebuilt Bosch injection pump, I have been searching the internet and have not been able to identify what engine it is for the number on pump Id tag is
0 403 236 005
any help is greatly appreciated
Reply Quote

Re: BOSCH INJECTION PUMP April 19, 2018 08:30AM
0 403 236 005
Perkins Phaser 180Ti 6.0L
Reply Quote

Re: BOSCH INJECTION PUMP August 19, 2019 04:29AM
Im trying to get a new shaft seal on the front of the pump and having a hard time finding it size is 17 28 3 mm number on pump is 0 460 494 115
Reply Quote

Re: BOSCH INJECTION PUMP August 19, 2019 05:20AM
What does the shaft measure 17 mm or 20 mm The 17 mm seal is P/N 1 460 283 312
Reply Quote

Re: BOSCH INJECTION PUMP May 13, 2020 04:17AM
Trying to find a more current part number for this pump and what it might fit. I cannot find any of these numbers anywhere online
From a metal tag

1342-021-4QG031322

1034-304

NP-PES3A65C310LS2000NP326

From a paper side tag

5-15600-602-0

From a front metal tag

Adjusted 360-1300 r.p.m.

NP-FP/RSV 200 1400 A024A11NP253

Assy Number 5410-165
Reply Quote

Re: BOSCH INJECTION PUMP tag numbers. Are 0445020039 cr/cp3s3/r110/30-789s sr # 06-06-26 100814 p/n 3972815 March 08, 2021 02:02PM
Need to replace my 07 Cummins injector pump. Sr # 06-06-26 10084--- 0445020039
Cr/cp3s3/r110/30-789s
P/n 3972815
Reply Quote

Newer Topic Older Topic

Author:

Your Email:


Subject:
Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message:
Website Statistics
Global: Topics: 38,777, Posts: 229,949, Members: 3,338.
This forum: Topics: 37,098, Posts: 226,034.

Our newest member Jacklovik2009