Some Beresford SD results June 18, 2011 04:11PM
6700 Open Farm

1. Mike Kats 560 355'99
2. Bill Jensen NH TD 95 347'66
3. Brian Blankespoor 1066 332'95
4. Mark Van Maanen 4020 331'00
5. Marv Huisman AC210 319'5

7500 Open Farm

1. Jared Dubbelde 4020 300'83
2. Mike Kats 560 299'33
3. Jarrod Hagena 4255 297'00
4. Brian Blankespoor 1066 286'34
5. Garry Bottjen 1466 282'96
6. Bill Jensen NH TD 95 278'83
7. Trevor Spenner 886 277'48
8. Marv Huisman AC210 264'72
9. Mark Van Maanen(couldn't get off the line)

8500 Open Farm

1. Mitch Larsen 4255 304'20
2. Jason Sweeter 1466 301'65
3. Matt Van Beek 856 301'28
4. Jared Dubbelde 4020 299'55
5. Clayton Rohmiller 4320 298'50
6. Nate Bottjen 1066 297'97
7. Junior De Yager 4040 291'00
8. Tim Huenink 1256 288'67
9. Trevor Spenner 886 272'68
Dan Bryan 4430(announcer was to busy doing tractor trivia to care about giving all the measurements it was terrible so we didn't get this measurement)

9500 Open Farm

1. Matt Van Beek 856 310'96
2. Bill Hassebroek 4430 309'46
3. Jason Sweeter 1066 308'78
4. Dan Bryan 4430 308'41
5. Kevin Van Beek 966 307'43
6. Dan Blankespoor 3688 307'28
7. Allen Shellum 4440 307'18
8. Junior De Yager 4040 306'68
9. Jeff Blankespoor 786 304'13
10. Terry Short 966 297'75
11. Clayton Rohmiller 4320 294'00
12. Gary Kavanaugh 986 293'92
13. Tim Huenink 1256 290'17
14. Dean Moller 4430 281'84
(There were some over rpms in the class but I did not catch who it was)

10,500 Open Farm

1. Kevin Van Beek 966 311'63
2. Bill Hassebroek 4430 307'36
3. Tim Blankespoor 3688 305'33
4. John Narigon 4455 301'92
5. Kevin Matthiesen 4055 301'88
6. Allen Shellum 4440 297'37
7. Dean Moller 4430 292'24
8. Lloyd Dekkers(Took off and fifty feet into it to quote Aaron Dekkers the rear end sounded like rocks in a blender)
Gary Kavanaugh 986 scratch
Travis Stene 1066 scratch
Terry Short 966 scratch

11,500 Open Farm

1. John Narigon 4455 290'54
2. Kevin Matthiesen 4055 285'14
Lloyd Dekkers Scratch
Travis Stene Scratch

11,500 Farm Stock

1. Lucas Driesen 4055
2. Mike Nieuwboer 1066
3. Kris Kjose 1066

10,500 Farm Stock

1. Taylor Kats 1466
2. Dan Bryan 4230
3. Bob Hustrulid 856

7,500 Farm Stock

1. Gary Knoch Super M 262'40
2. Mike Sandbulte 560 261'25
3. Chris Garris 5000Ford 197'85
4. Troy Thiessen 2520 185'39

6,700 Farm Stock

1. Mike Sandbulte 560 316
2. Gary Knoch Super M 258
3. Troy Thiessen 2520JD 257'2
4. Chris Garris 5000Ford (did not catch measurement)

8,000 Super Stock Pickup

1. Nathan Bandstra Durmax
2. Drew Grosz 02' Dodge

7,500 Stock pickup 4wd

1. Mason Hedgen 2002 Dodge 260'25

Final thoughts on Beresford SD, probably get a different announcer. He went way overboard on his tractor trivia games that I'm pretty sure he didn't realize there was a tractor pull going on in front of him it was pretty bad. It was pretty cool to have some exhibition runs form Curt Jensen of the Dubuque Iowa region, who came all the way to Beresford SD. so friends and family could see him pull. He runs the Tasmainian Deere Super Farm with the Tri-State tractor pullers out that way. We also got to see Ron Fischers Fischer Nutz Outlaw 4wd truck make a pass. All in all good pull, track was tricky and I think fooled a lot of people. It had looked like some people thought to go big gear, and she had more bite and traction than it appeared. I will also run my little disclaimer everytime I do post results, these are very unofficiall feel free to correct me. I didn't get all the measurements, and where there is no distanced listed thats just way the top three had finished. Plus some of the pullers listed were dqed on rpms and I not sure which ones. Special thanks goes out ot everybody in Beresford invloved with the pull for all the hard work they did allowing us to pull there.

The Great Plains Tractor Pullres travel to Garretson SD next Friday, the 24th and Pipestone Mn on the 25th. Good luck to everybody in Garretson next Friday.
Reply Quote

Re: Some Beresford SD results June 19, 2011 12:27AM
"rocks in a blender",that just makes a guy cringe..
Reply Quote

Newer Topic Older Topic

Author:

Your Email:


Subject:
Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message:
Website Statistics
Global: Topics: 38,777, Posts: 229,949, Members: 3,338.
This forum: Topics: 37,098, Posts: 226,034.

Our newest member Jacklovik2009