Page 1 of 3
Pages: 123
Results 1 - 30 of 67
that's exactly how I have it done....makes a closed loop system works great I use factory orbital valve my cylinder is not quite that big bit I don't see that being a problem
by
1066puller
-
Forum
400 series stock front cover with cam access $400
tapered turbo spacer block 3in $350
billet injector hold downs for stock style injector $350
billet front cover with drop legs and accessory drive
mezire intercooler pumps
older hyper 4.1 turbo with 32 housing $2500
24.5x32 firestone single cut pullers on Midwest wheels 16in backspace very nice set no chords $4500
24.5x32 fi
by
1066puller
-
For Sale
ih hot farm you can buy it the way it is or I can finish it for you all it needs is put together and plumbing. The motor trans and rear all together ready to go. Rear end has hitch and wheelie bars with atlas billet diff. Trans has all atlas gears direct 1 2 3 over with figure 8 support and solid bottom shaft. The motor is 540ci setup to run with an intercooler ( currently do not have a cooler)
by
1066puller
-
For Sale
4.6 wimer small cover 32 exhaust housing $4200 obo
7172153818
can bring to Shipshewana
by
1066puller
-
For Sale
Not sure why Joey is getting thrown under buss here to my knowledge nothing like this has happened in pulling for a long time if ever so nobody truly knows what's going to happen from here but I would hope that your concerns should be on this family and the puller instead of trashing a person, club or organization
FURTHERMORE if you haven't realized this EVERYONE who is involved in p
by
1066puller
-
Forum
60371 r2 I'm told there is a lighter casting then this but dose anyone know how much lighter?
by
1066puller
-
Forum
I don't disagree I believe if we could turn back time 20.8s would the tire limit....there's alot of things that have gotten out of hand....
by
1066puller
-
Forum
the problem with a box turbo rule is no two turbos are the same....this has been proven on the dyno time and time again so that's part of the reason east coast moved on and also part of the reason interstate pro farm is hurting right now....of course there are other factors that play into this
by
1066puller
-
Forum
has anyone used on off a 2012 6.7 cummins? I know some have uusone off a 5.9
by
1066puller
-
Forum
I'm looking to buy a new skid loader I need it to do well in dusty dirty conditions so cab is a must....what should I consider???
by
1066puller
-
Off-Topic Forum
looking at building an engine stand I like twisters but they are a little pricey and I've tried to call them with no call back so I was wondering if anyone has a "must have feature " before I get started thanks in advance
by
1066puller
-
Forum
Does anybody know the part number of the light 706 rear??
by
1066puller
-
Forum
looking for a nice setup for a 3way dump any suggestions
by
1066puller
-
Forum
not sure why yours in only engaging half way but I have a gear reduction starter to go into stock location 7172153818
by
1066puller
-
Forum
it gose inside trailer and uses factory doors
by
1066puller
-
Forum
I built my own....make it heavy and if you use a winch dont go with an atv winch....i used a 12k lb winch from harbor freight....yes its overkill but like said above if it falls and hurts anyone you will have to live with it....i make sure everyone is clear when going up and down.....if you make it to light it will bend and once its bent then its going to look like @#$%& lol
by
1066puller
-
Forum
what organization do you want to run with?
by
1066puller
-
Forum
in gordyville?
by
1066puller
-
Forum
dose everyone need to buy the turbo from the same place?
by
1066puller
-
Forum
the club i pull with is interested in possibly going to a box turbo rule....what I would like to know from other pullers who already have a rule like this in place is dose this work? is there ways around a "seal"? Dose this cost more in the long run considering some may go to the dyno more often and spend huge amounts in other places? any and all input is appreciated
by
1066puller
-
Forum
why do you say 20s are harder to turn?
by
1066puller
-
Forum
I know its a long way off yet but will gordyville 2021 happen? Here in PA they just announced a virtual only farm show set to be in January....wondering if IL is as messed up as PA
by
1066puller
-
Forum
Most guys are running s400....are you looking to build for this class?
by
1066puller
-
Forum
What about the swivel fitting what do you have there
by
1066puller
-
Forum
What pump are guys using to externally lube ih diff?
by
1066puller
-
Forum
You dont realize the pressure and heat inside that tube....if you watch close you can see it swell with the pros and supers....
by
1066puller
-
Forum
What do you use to keep nice away from combines and other equipment?
by
1066puller
-
Forum
What class are you building for
by
1066puller
-
Forum
wanting to put a ramp door on my pulling trailer would like to keep the original doors but don't need to I can build it myself but im looking for some opinions and pictures on the best way to go about this winch vs hydraulic ect.... thanks
by
1066puller
-
Forum
Interested in your tires call me 7172153818
by
1066puller
-
Forum
Page 1 of 3
Pages: 123