Page 3 of 3
Pages: 123
Results 61 - 86 of 86
The part number is 670678c91. The rods I have for sale are take outs from a running 1456 and would like $500. I also have a brand new set from IH. I do not see a casting number on either set.
by
followme1086
-
Forum
Thanks, that clears up everything, sounds like the begining of a good class. Are you running the 44 in superfarm?
by
followme1086
-
Forum
Travis, Is this new class in addition to the prostock class or a combination of the existing prostock class? I did not see a cube limit in the rule book for the pros. If I understand correctly altered tractors can run a cage now and must have non cut tires as always. thanks in advance By the way I to think the VT boys are a class act!
by
followme1086
-
Forum
Wondering what the tooth count is on a 656 bull pinion? I know there are 13/49 14/49 and 16/49 ring and pinions and the bull gears have 66 teeth. Trying to figure final drive ratio.
by
followme1086
-
Forum
Hi Ed I lost your number give me a call sometime. I have a fiberglass nose with your name on it.
by
followme1086
-
Forum
Hey Rich, what are the rules for enhanced? What sled? Thanks
by
followme1086
-
Forum
7100, 7200, 8900, mx180 mx200 mx220 mx210, mx230 all have 8.3 with mech injection. mx240 mx270 mx255 mx285 have 8.3 with caps pump 24 valve mx215 mx245 early mx275 have HPCR 8.3 Later mx275 mx305 mx335 have HPCR 9.0
by
followme1086
-
Forum
Any pictures? "The Rattler" is sharp and would like to see "Logan's Run"
by
followme1086
-
Forum
Is there a new 88 series IH pulling in TN or KY? Race or Tackett? any pictures?
by
followme1086
-
Forum
Any results?
by
followme1086
-
Forum
Any results for LPS 8500lb class?
by
followme1086
-
Forum
Someone impressed with how the tractor looks and runs! Saw the tractor at DuQuoin in 2008!
by
followme1086
-
Forum
Any pictures or videos of "All In"?
by
followme1086
-
Forum
mountuptonpulling.com
by
followme1086
-
Forum
What is the one day hook amount?
by
followme1086
-
Forum
Does the pull start at 5:30 saturday?
by
followme1086
-
Forum
13 on the bull pinion and 73 on the bull gear
by
followme1086
-
Forum
I could have worded that alot better, your post was much better sorry and thanks.
by
followme1086
-
Forum
With a 13/49 ring and pinion each gear would be about 4 percent faster not quite one tooth faster for each gear. Each tooth on the speed trans gears would be about 6 percent difference.
by
followme1086
-
Forum
What are PPL hot farm rules? Their site rules are being updated?
by
followme1086
-
Forum
I am not sure about a dock but the pull starts at 10 and I beleive there are stock and enhanced classes 5500 7500 9500 10500 11500 13500 15500 stock and 7500 9500 10500 11500 enhanced rules like Madison county fair in Brookfield NY
by
followme1086
-
Forum
I had a 13mm model 100 run away after getting it back from the shop and found out the fuel control rod from the govenor had come off. Also heard of the rod breaking on old school pumps where the rod is ground for clearance. The stuck plunger could be a result of, or happened after a control rod failure. Just my experience.
by
followme1086
-
Forum
763-780-9548 ask for carl
by
followme1086
-
Forum
Where and who is Precision Turbo? How is the quality, performance ,and price?
by
followme1086
-
Forum
Allied Precision 712-335-3154
by
followme1086
-
Forum
A466 with a tractor rear cover from a 66 series will bolt upto 06,26,56,66,and 86 transmission housings. Front frame rails are an issue, but can be done.
by
followme1086
-
Forum
Page 3 of 3
Pages: 123