Page 2 of 3
Pages: 123
Results 31 - 60 of 69
The 4x.015 have more total hole opening area than 5x.013.
by
DK Case
-
Forum
Did you try Atlas?
by
DK Case
-
Forum
Are the large journal 504 rods heavier than the small journal 504 rods? How much will the large journal rods take before they need hardening? Thanks
by
DK Case
-
Forum
Are you taking it farm pulling or want to build it bigger? Even in farm pulling the powershift needs some adjustments to hold if you have it running good. And if you're going bigger than farm pulling find a Case with a manual 8 speed transmission.
by
DK Case
-
Forum
Will these be delivered before Friday?
by
DK Case
-
Forum
Security Race Products
by
DK Case
-
Forum
Go to a truck shop, they should be able to have bolts made to your specs like they do for truck axle springs. They'll be fine thread and high strength.
by
DK Case
-
Forum
I sent the email to Case
by
DK Case
-
Forum
I sent you an email.
by
DK Case
-
Forum
If it's the original engine, it's large journal. An early one would not have the oil spray to the bottom of the pistons and would have the smaller oil pump. Laters one had large journal, oil spray & big oil pump. I'm not sure where the break is between early and late. 1370 heads have pencil injectors, 1570 and later have large body injectors.
by
DK Case
-
Forum
This post has parts listed for cylinders and a hand pump: Helm Pump Steering
pulloff.com/phorum/read.php?2,261879,261879#msg-261879
by
DK Case
-
Forum
The 2019 rules meeting and awards banquet will be held on January 18, 2020 at the VFW in Hartington, NE.
The meeting will begin at 2:30pm with the social beginning at 5:00pm and the meal and awards at 6:00pm.
Contact Benny Vee or B.J. Lund with questions.
by
DK Case
-
Forum
I think Atlas makes pulleys to fit aftermarket dampeners.
by
DK Case
-
Forum
What hub are you going to use to run the aftermarket dampener? I know Atlas makes one, are there other companies that make the hub for a Case?
by
DK Case
-
Forum
Hawthorn Tire had some a while back
by
DK Case
-
Forum
Do you still have the pistons? I sent you a pm.
by
DK Case
-
Forum
I'd be interested in seeing pictures too: 4 O two 7 five O 9 seven three 8 Thanks
by
DK Case
-
Forum
Aug 8th Northeast Nebraska Pullers at West Point starts at 5:00 followed by MATTPA and Outlaws are in Weeping Water. Aug 9th NE Bush Pullers in West Point, the MATTPA and Outlaws are in Gibbon. Aug 10th Northeast NE Pullers at Bloomfield, NE Bush at Norfolk & Aug 11th Pickrell is an open pull
by
DK Case
-
Forum
No water injection, limited to a box 3LM466 turbo.
by
DK Case
-
Forum
Would a 504 from a 2594 in a 1070 be in the same timing area, 32, for a 3000/3200 rpm class with a 5x20 dual feed injectors and 10 mm pump?
by
DK Case
-
Forum
There was one advertised in Dec/January somewhere in WI, that one was sold when I contacted him.
by
DK Case
-
Forum
IH FRAMES - AIR RIDES - WHEELIE BARS - HITCHES
by
DK Case
-
Forum
We've had a couple, always good trailers for us.
by
DK Case
-
Forum
Here's a link to a list of pulls that I put together for pulls with Northeast Nebraska Pullers, West Central Iowa Pullers, and Great Plains Truck & Tractor Pullers. Also included are pulls with The Big Red Sled which covers some non-association pulls too. It also has the MATTPA, NE Bush and Outlaw Pulls. There's also a farm pull in Leigh NE on 7/20/19 that's not listed. And The
by
DK Case
-
Forum
Have you had any problems with the 3/16"? Not sure whether to go with 3/16" or 1/4", it will be going on a Case 1070. JD4430 what did you end up using? Thanks
by
DK Case
-
Forum
1/19/2019, rules meeting @ 4 pm, followed by social hour and banquet @ Hartington VFW.
by
DK Case
-
Forum
Will the 1.93 pump work on a 9700 lb tractor? Or would the 1.21 cu in pump be better?
by
DK Case
-
Forum
Paid $200/set to get 38" steel wheels widened. Used an extra rim so there's only 1 weld on each rim.
by
DK Case
-
Forum
On my open station 1070 8 speed I got it down to 7700, stock 451 with no turbo, with me on it and no weights except the weight brackets. I had a narrow front end, fiberglass nose, and removed: seat & seat base, fuel tank, air cleaner assembly, hydraulic cooler, hydraulic filter, rockshaft, hydraulic boxes, and rear hitch support with sway blocks. I have the short axles with 3 3/16" axles so I did
by
DK Case
-
Forum
Page 2 of 3
Pages: 123