Page 1 of 6
Pages: 12345
Results 1 - 30 of 177
Funny you ask.. this tractor was see at Osage IA last summer pulling. it indeed has a automatic transmission inside!
by
Mueller
-
Forum
Looking for 20.8R38 Double cut. Preferable Deep Treads or Pro Pullers.
6zero8-7three2-zero65three
by
Mueller
-
Wanted
From Jason's Family history I would assume the new DSS would be a D21 in remembrance of his father's past D21 DSS "BlackJack"
by
Mueller
-
Forum
ATTN:We have had a GENEROUS local donation for the 9500 Hot farm 20.8 Class Purse on Friday Night June 16th!
This is a fun class which brings our neighboring associations together. Everyone runs their association rules!
by
Mueller
-
Forum
For everyone's awareness this is the best route to the pits & Cuba City's track
From Main Street / HWY 80 Turn to the East at Sloan Implement on Roaster RD. Then turn left at IAS feed mill that will bring you directly into the rear of the Pits. Signs will be along the route in town accordingly.
by
Mueller
-
Forum
Cuba City Power Pull Weekend back in full force in 2023
June 16th & 17th 2023 - 7pm start time both nights
Splinter park (by water tower), Cuba City WI
FOOD AND DRINKS on grounds from local 4-H and local community groups
Featuring ECIPA classes along with local classes Friday Night and TRI STATE Truck and tractor on Staurday Night
SEE ATTACHED FLYER FOR DETAILS
by
Mueller
-
Forum
I running an Urmson 4 speed (No quad) so i cannot speak on my own tractor. Also never been on a Dyno
A fellow tractor was running wet clutch/ Built 4430 quad(Direct and under)/original 4440 trans for some time running before having issues at that 1000+/- area.
by
Mueller
-
Forum
I have a 4 disk atlas Wet Clutch that will be coming out in the next few weeks and will be for sale. 1/4" floaters that could be exhanged for thinner floaters to allow a additional disk(5th disk) Latest and Greatest from Karl and he was great for support. I am only removing as we have began to out run the clutch's capabilities. 6zero8-7three2-zero6five3
by
Mueller
-
Forum
Honda Pioneer 1000, 3 seat or 5 seat. Direct Drive Transmission for pulling (No belt)
Honda Pioneer 1000
Honda Pioneer 1000 5 seat
Length
117 inches
Width
63 inches
Height
76.9 inches
Wheelbase
80.2 inches
by
Mueller
-
Forum
ECI had done that YEARS ago due to equipment failure.
If sled equipment has issues ECI now will resort to using a Radar speed board.
by
Mueller
-
Forum
Just a little light from my small corner of WI as i feel we have evolved to a good system.
We run pulling weekend event in Cuba City WI. Originally a brush show on Friday evening with local classes and Tri-state pullers on Saturday. General admission was $8 and pit passes were $10 per event (children free). Brush show always had the $20 entry fee and received 2 free pit passes. Tristate puller
by
Mueller
-
Forum
Just a little light from my small corner of WI as i feel we have evolved to a good system.
We run pulling weekend event in Cuba City WI. Originally a brush show on Friday evening with local classes and Tri-state pullers on Saturday. General admission was $8 and pit passes were $10 per event (children free). Brush show always had the $20 entry fee and received 2 free pit passes. Tristate pulle
by
Mueller
-
Forum
Get hitch as close to the drawbar support as possible. Usual rule is minimum 18" back from axle center and 20" MAX height
Suggestion - find a broken drawbar and weld a 3.5-4" loop onto the drawbar
by
Mueller
-
Forum
Well i can chime in a little here. I currently have a 8.1 powertech mechanical fuel in my pulling tractor. Currently has a wet clutch (soon to be remedied with a dry).
the 8.1 has the small 4bolt pattern for the frame rails
40 series cast oil pan will bolt on & allows bell house to seal for wet clutch - Need to switch oil sump pick up on oil pump
Front HYD pump - I was able to attach the
by
Mueller
-
Forum
Cuba City Power Pull Weekend June 17th & 18th 2022
See attached flyer for details!
by
Mueller
-
Forum
We transitioned to a new hook fee design a few years ago. Seems to be working for our small town event with allowing 1 hook per each pulling vehicle very well.
Previously we charged 8-10 admission but pullers didn't pay admission. We charged a $20 hook fee that came with 2 pit passes($20 value)
Currently we have went to a Flat $10 admission/pit pass for everyone & We do not charge a ho
by
Mueller
-
Forum
i used this Stainless steel polished pipe form summit. Awesome stuff.
by
Mueller
-
Forum
Do you have a part number for the Intellitronix tach? we use a crank based magnet for our sled monitored data logger. sounds simple to add this tach to the existing system...
by
Mueller
-
Forum
Cuba city's flyer showing all local classes to accompany the ECI classes Friday night!
by
Mueller
-
Forum
Does anyone have insight into changing gears in a 4speed trans? I am to believe this is a Urmson transmission but am not certain. I have extra gears but am not certain on the change out process. Also any information on if this transmission is capable of having a PARK in it would be helpful.
Thanks in advance
Brian Mueller
Current gear shift pattern is as follows
1st gear = D Range & 1st
by
Mueller
-
Forum
FVP is advertising a set up like your looking for
by
Mueller
-
Forum
Grant county fair, lancaster Wi
by
Mueller
-
Forum
I am working with a JD powertech 8.1 and am curious if I can utilize the factory tack pick up with a gauge such as a Intellatronix digital tachometer?
by
Mueller
-
Forum
2019 Cuba City Power Pull weekend June 14 & 15. 7pm start on both Friday and Saturday. See flyer for details
Parade Saturday at 2 PM on Washington street.
by
Mueller
-
Forum
Anyone have any luck running a ATI balancer on a JD 8.1? any way to still use front hyd pump and alternator with this balancer?
by
Mueller
-
Forum
Attention FRIDAY NIGHT pullers! We will NOT be charging a hook fee this year but everyone will be required to purchase a $10 pit pass.
This will eliminate some congestion at the sign in table while the end cost will remain the same. Previously we provided 2 pit passes ($20 value)with the 20 dollar hook fee.
See everyone this weekend!
by
Mueller
-
Forum
2018 Cuba City power pull weekend June 15th and 16th
https://www.facebook.com/Cuba-City-Power-Pull-Truck-and-Tractor-Pulls-1443072865985152/]
by
Mueller
-
Forum
We have allowed 10MPH in turbo farm stock classes(11k,13k,15k) with no upshifting after the first 100ft (same as shut down) Seems to be working in SW WI.
by
Mueller
-
Forum
I believe Kevin Engelking's New Limited pro(or could be light pro(I'm not sure)) white 125 is a 8.3 cummins. He also runs a dyno service. Probably a good guy to talk to.
Kevin Engelking 815 865 5564
by
Mueller
-
Forum
Page 1 of 6
Pages: 12345