11:33:35am, Sunday, May 19, 2024
john deere wet clutch
|
Registered: 01/27/2013 Posts: 44 |
I was needing some info on where to get a 5 disc clutch set up at. Took to dealer an didn t hold. They wasn t familiar with what I was doin with the hubs welded together. Would like to know of anywhere in southern ky or middle tenn that was experienced. Thanks for any help! |
Re: john deere wet clutch
|
Anonymous User
|
you looking for main perma clutch or the quad range hi/lo i can probly help if you let me know which |
Re: john deere wet clutch
|
Registered: 07/11/2008 Posts: 326 |
What were you running?? 4 disk with the welded hubs and Mod to the hydraulic activation?? or just a 2 disk?? |
Re: john deere wet clutch
|
Anonymous User
|
i run welded hub and 4 disc with mod to control valve and 220 psi rusch make parts to make it 5 disc and sfi certified |
Re: john deere wet clutch
|
Registered: 07/11/2008 Posts: 326 |
JD tech.. Sorry.. I was directing that toward Risky..
I'm not sure, but if Kenny's pulling parts might have something also.. (Might be closer than rusch, but I know they have the parts.). You could also try messaging KTA on here, he's done a bunch and would be close to you.. |
Re: john deere wet clutch
|
Registered: 01/27/2013 Posts: 44 |
The main clutch is was I was asking about.I was running a 3 disc an have welded hub up an made a 5 disc now. Just don t think I got a good job setting it up at dealer. Had a 180 psi but slipped it on 2nd pass. |
Re: john deere wet clutch
|
Registered: 07/11/2008 Posts: 326 |
How did you modify your oil flow.. there are a couple of different ways to get the oil to the PTO clutch.. You can Modify the valve.. or remove part of the lube reduction valve.. you just have to plug off some of the ports.. |
Re: john deere wet clutch
|
Registered: 01/27/2013 Posts: 44 |
Well it was a last min deal an all I done was tied up pto lever but have got it all apart now an goin to fix lube valve. |
Re: john deere wet clutch
|
Registered: 07/11/2008 Posts: 326 |
If you didn't change the oil flow.. you should have had to engage the PTO lever at the same time as you engage the foot pedal.. or very soon after...
When you remove the bottom half of the lube reduction valve.. Just make sure you plug off the PTO Brake, and PTO supply at the cross over tubes or very close.. (at the tubes is usually the easiest.) I'd leave the shaft in to help support the PTO hub, but some dont... I have had friends have the dealer set them up without any issues... |
Re: john deere wet clutch
|
Registered: 01/27/2013 Posts: 44 |
Ok thanks, An what shaft u talking about leaving in for support |
Re: john deere wet clutch
|
Registered: 07/11/2008 Posts: 326 |
The shaft that the PTO hub drives.. I've seen the inside of the PTO hub cut out on some.. It's not a must do, just nice to have the extra support of the hub.. Most likely you'll have the rest of the PTO gutted so it's not turning anything.. |
Website Statistics
Global: Topics: 38,780, Posts: 229,958, Members: 3,338.
This forum: Topics: 37,099, Posts: 226,041.
Global: Topics: 38,780, Posts: 229,958, Members: 3,338.
This forum: Topics: 37,099, Posts: 226,041.
Our newest member Jacklovik2009