Re: Boone/farm progress pull

	Boone/farm progress pull August 19, 2014 07:49AM
IAfarmer	What are the classes and time for the pull at Boone this year? Reply Quote

	Re: Boone/farm progress pull August 19, 2014 01:32PM
PPL Puller	85-95LPS, 6-8SS, 9PF Reply Quote

	Re: Boone/farm progress pull August 19, 2014 01:37PM
Jdkidd	What are the dates Reply Quote

	Re: Boone/farm progress pull August 19, 2014 02:12PM
IAfarmer	Are they not having the pro stocks this year? Is it the same both nights? Reply Quote

	Re: Boone/farm progress pull August 19, 2014 02:15PM
Bryan Lively Moderator Registered: 01/11/2009 Posts: 1,579	8/26 & 27; 95pf, 85 & 95 Lps, 8000ss and lss. Bryan Lively - Reply Quote

	Re: Boone/farm progress pull August 19, 2014 03:46PM
yanmar55 Registered: 03/12/2010 Posts: 405	What is RPM limit and cubic inch limit in 95 pro farm? weight is 9500, correct? Reply Quote

	Re: Boone/farm progress pull August 19, 2014 04:30PM
bc35 Registered: 01/19/2010 Posts: 105	C'mon man, you were just in the discussion about this yesterday, I just saw it on the 2nd page!!! Reply Quote

	Re: Boone/farm progress pull August 20, 2014 12:31AM
yanmar55 Registered: 03/12/2010 Posts: 405	Your right, if I would have gotten the right information yesterday, I wouldn't have to be asking again. What's this forum for? Reply Quote

	Re: Boone/farm progress pull August 20, 2014 01:10AM
$0.02	3500 and 466. Reply Quote

Re: Boone/farm progress pull August 20, 2014 01:22AM

Anonymous User

WESTERN SERIES MODIFIED SEE PAGE 57 (ESP & NYTPA MOD) PRO-FARM
1. Weight – 9,000 lbs. P-pump, 9,500 lbs. A-pump
2. Engine- Maximum 470 cubic inches. OEM stock block, head, intake manifold & exhaust manifold must be used for make and model of vehicle being entered. No aftermarket components allowed.
3. Chassis - Maximum of 114” wheelbase unless originally produced with a longer wheelbase at which point the wheelbase will remain stock. Maximum length of 13 feet from center of rear axle to forward-most point of vehicle excluding the front hitch.
4. Tires - 20.8-38 ONLY
5. RPM - 3500 RPM maximum. Vehicle must have an ISSPRO #019R8906 magnetic pickup attached to the front of the engine to measure engine RPM’s. The lead from the pickup to the rear of the vehicle is to be made of 14-16 gauge wire attached to a 110V, 3 prong female electrical outlet. The 2 wires from the pickup need to be attached to the 2 main spades, not the ground spade, of the electrical outlet. This outlet receptacle needs to be mounted next to the rear mounted air shutoff cable. Wire must be one
(1) continuous wire outside the side rails and visible. NO SPLICES.
6. Fuel Pump - Bosch P series pump allowed Model 3000 and 7100 only, No 8600 series allowed. 13mm plunger diameter maximum. Only one plunger per cylinder allowed.
7. Turbo - STOCK GARRETT GT42 3” by 3”. Any internal alterations to either the intake or exhaust side will be deemed illegal and the competitor will receive a LIFETIME BAN NOT ONLY FROM the PRO FARM class, but from ALL FUTURE P.P.L. competition. Exhaust housing mounting pattern must not be any larger than 2.75” X 3.5”.

Reply Quote

	Re: Boone/farm progress pull August 20, 2014 01:47AM
so yanmar	What info did u get that was incorrect? Reply Quote

	Re: Boone/farm progress pull August 20, 2014 09:45AM
yanmar55 Registered: 03/12/2010 Posts: 405	Nothing was incorrect. According to the PPL website on the schedule, it only mentioned 9500 Pro Farm, not 9000. Nothing was clear until case fan listed the rules. I looked in the rule book and no pro farm is listed in contents pages. How was I to know that the rules for pro farm was in Western Series section of the book? End of subject. Reply Quote

	Re: Boone/farm progress pull August 20, 2014 01:36PM
hey yanmar	Will we see you at boone? Reply Quote

Re: Boone/farm progress pull August 20, 2014 02:13PM

Klint

Registered: 03/26/2010
Posts: 139

I have been getting some questions about our two Super Stock classes the event at Boone, Iowa August 26 and 27th. Our rules are listed below:

Prairie Brand Seed 8,000 lb. Super Stock class:
Class weights:
1. 8000 lbs. Alcohol tractors below 650 c.i.d to 510 c.i.d. tractors with overhead cams
2. 8,200 lbs. Alcohol tractors below 650 c.i.d tractors with push rod engines, and Below 510 c.i.d. with overhead cams.
3. 8,500 lbs. Below 650 c.i.d. Component Diesel Super Stocks and Below 505 c.i.d. alcohol tractors with pushrod engines.
4. 9,000 lbs. Pro Stock tractors: Below 680 c.i.d. with one unlimited sized turbocharger. OEM Chassis Diesel Super Stocks.
5. 9,500 lbs. Limited Pro Stock tractors: Below 640 c.i.d. with one 4.1” turbocharger and Below 540 c.i.d. tractors with one turbocharger of UNLIMITED size.

Prairie Brand Seed Light Super Stock class:
Weights:
6,200 lbs. Below 505 c.i.d. alcohol component tractors with pushrod engines
6,400 lbs. Below 505 c.i.d. alcohol-cast rearend tractors with pushrod engines
6,700 lbs. 504 c.i.d. Diesel Super Stocks and Below 370 c.i.d. alcohol tractors with pushrod engines and 640 c.i.d. tractors with one 4.1 turbocharger
7,000 lbs. "Light Limited Super Tractors: 410 c.i.d. and below with a intercooler are limited to one 3"" by 4"" turbocharger with NO MAP INHANCEMENT GROOVES: 315 c.i.d. and below with a intercooler are limited to two 3" by 4" turbochargers with NO MAP INHANCEMENT GROOVES, OR 410 c.i.d. and below with NO INTERCOOLER are limited to one 3" by 4" turbocharger with MAP INHANCEMENT GROOVES, OR 466 c.i.d. and below Diesel and 370 c.i.d. and below Alcohol are limited to one 3" by 4" turbocharger with NO MAP INHANCEMENT GROOVES. MAP grooves limited to 0.250”.

Purse payouts: 8,000 Super Stock is a $4000 class paying $1000 for first paying back 10 places, the Light Super Stock class is a $4200 class paying $1000 for first and paying back ten places also. We allow tractors to hook in both classes if desired. Non member hook fee is $90.00 each night. If you have any questions feel free to give me a call at 309-712-1406 . Thanks Klint Tucker, Competition Director of the PPL Western series. Hope to see everyone next week.

Reply Quote

	Re: Boone/farm progress pull August 21, 2014 01:49AM
AV Registered: 03/26/2008 Posts: 744	What's per hook fee? And anything special with PPL needed not covered under NTPA or Outlaw safety requirements? COO for OTTPA www.outlawpulling.com www.truck-specialties.com Schaeffer Oil Representative [www.schaefferoil.com] Reply Quote

	Re: Boone/farm progress pull August 21, 2014 05:21AM
MG1206	It said one time hook fee is $90 Reply Quote

	Re: Boone/farm progress pull August 21, 2014 05:30AM
AV Registered: 03/26/2008 Posts: 744	You are right it did my mistake. COO for OTTPA www.outlawpulling.com www.truck-specialties.com Schaeffer Oil Representative [www.schaefferoil.com] Reply Quote

	Re: Boone/farm progress pull August 21, 2014 01:21PM
Hot Binder	What time does it start each day? Reply Quote

	Re: Farm Progress Ad at top of page August 22, 2014 02:53AM
Anonymous User	Still not seeing the start times for these events at progress show? If you want to get a crowd need to get some advertising out their have yet to see any flyers about this event anywhere around boone. Reply Quote

	Re: Farm Progress Ad at top of page August 24, 2014 03:43PM
Super M	Gates open at 4, event starts at 6 both nights Reply Quote

	Re: Farm Progress Ad at top of page August 25, 2014 01:15PM
Hot Binder	Does it for sure start at 6? I also seen places that say the pull starts at 2 tomorrow and 11 on wednesday Reply Quote

	Re: Farm Progress Ad at top of page August 25, 2014 01:29PM
Bryan Lively Moderator Registered: 01/11/2009 Posts: 1,579	Wherever you saw an afternoon time it was incorrect. 6pm both nights Bryan Lively - Reply Quote

	Re: Farm Progress Ad at top of page August 25, 2014 01:36PM
Hot Binder	Thank you, hopefully the weather cooperates Reply Quote

	Re: Farm Progress Ad at top of page August 26, 2014 12:39AM
Larry B	Could we get a weather update? Reply Quote

	Re: Farm Progress Ad at top of page August 26, 2014 01:22AM
Bryan Lively Moderator Registered: 01/11/2009 Posts: 1,579	Rain this morning, looks like it is moving out early afternoon. Bryan Lively - Reply Quote

	Re: Farm Progress Ad at top of page August 26, 2014 02:20AM
af	So we should get to go pulling to night. We can load up and head that way Reply Quote

	Re: Farm Progress Ad at top of page August 27, 2014 07:56AM
midwest pull fan	Haven't heard anything about Farm Progress pull. Did it get rained out or what. How many pullers did they have and how many people in the stands. Is it on for tonight or rained out. Reply Quote

	Re: Farm Progress Ad at top of page August 27, 2014 08:31AM
Big Block Deere Registered: 03/26/2008 Posts: 376	Lots of good iron in the pits. The stands were a little bare to start but more people started coming in as the night progressed. I think if they could have it at the Farm Progress Show grounds instead of the fair grounds you would see a better crowd. Reply Quote

	Re: Boone/farm progress pull August 28, 2014 01:34AM
Mark Registered: 04/07/2008 Posts: 781	any results Reply Quote

	Re: Boone/farm progress pull August 28, 2014 02:21AM
Found them	Power & Noise site has them. From the looks of the pictures on there not many big name tractors at the pull and looks like maybe 500 people in the stands at the most. Reply Quote

	Re: Boone/farm progress pull August 28, 2014 02:32AM
?	What do you consider a big name tractor? Reply Quote

Re: Boone/farm progress pull August 28, 2014 02:53AM

Found them

With al the hype on this website that had a thread at the top for a month advertising the pull. Adding Midas Tire and all the hoopla, I figured it would have more of the bigger PPL classes like big Pro Stocks, Mod tractors or something like that. The 4.1 class was good, but after that 5 light supers, 4 big supers and some of them were from the light class, hot farm & pro farm. With the little crowd they had probably couldn't afford that kind of pull anyway.

Reply Quote

	Re: Boone/farm progress pull August 28, 2014 03:13AM
JOHN	FOR YOU NA SAYERS,STAY HOME OUT OF THE REAL PEOPLE PULLERS WAY,LIVES AND OUR WORLD,-- found them....... Reply Quote

Re: Boone/farm progress pull August 28, 2014 04:08AM

ace

Thought it was a really good show good sled settings for most part track wasn't great Wednesday for alky tractors but the rain Tuesday didn't help love the 4.1 lim pros. I hope they do this again in 2 years the crowd wasn't great Wednesday the advertising for this show wasn't good gotta get some ads on radio and in newspapers. Good job Jason Shultz announcing sounded good. hope they keep doing it.

Reply Quote

	Re: Boone/farm progress pull August 28, 2014 04:51AM
to found them	I guess with all the hoopla and the poster on here for you to read you'd have known it was a Western series hook not a champions tour hook ;-). It appeared to me that some of the biggest names in the sport were there in the classes offered.... Reply Quote

Newer Topic Older Topic

Print View RSS

Author:

Subject:

Help information

Spam prevention:

Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.

Enter code:

Message:

[quote="Anonymous User"]
WESTERN SERIES MODIFIED SEE PAGE 57 (ESP & NYTPA MOD) PRO-FARM
1. Weight – 9,000 lbs. P-pump, 9,500 lbs. A-pump
2. Engine- Maximum 470 cubic inches. OEM stock block, head, intake manifold & exhaust manifold must be used for make and model of vehicle being entered. No aftermarket components allowed.
3. Chassis - Maximum of 114” wheelbase unless originally produced with a longer wheelbase at which point the wheelbase will remain stock. Maximum length of 13 feet from center of rear axle to forward-most point of vehicle excluding the front hitch.
4. Tires - 20.8-38 ONLY
5. RPM - 3500 RPM maximum. Vehicle must have an ISSPRO #019R8906 magnetic pickup attached to the front of the engine to measure engine RPM’s. The lead from the pickup to the rear of the vehicle is to be made of 14-16 gauge wire attached to a 110V, 3 prong female electrical outlet. The 2 wires from the pickup need to be attached to the 2 main spades, not the ground spade, of the electrical outlet. This outlet receptacle needs to be mounted next to the rear mounted air shutoff cable. Wire must be one
(1) continuous wire outside the side rails and visible. NO SPLICES.
6. Fuel Pump - Bosch P series pump allowed Model 3000 and 7100 only, No 8600 series allowed. 13mm plunger diameter maximum. Only one plunger per cylinder allowed.
7. Turbo - STOCK GARRETT GT42 3” by 3”. Any internal alterations to either the intake or exhaust side will be deemed illegal and the competitor will receive a LIFETIME BAN NOT ONLY FROM the PRO FARM class, but from ALL FUTURE P.P.L. competition. Exhaust housing mounting	pattern	must	not	be	any	larger	than	2.75”	X	3.5”.[/quote]

Website Statistics

Global: Topics: 38,639, Posts: 229,705, Members: 3,325.
This forum: Topics: 37,067, Posts: 225,903.

Our newest member JD_8520