River Falls FFA Alumni Tractor Pull - July 9th 2016
|
River Falls FFA Alumni Tractor Pull: July 9th 2016
"The Legacy Continues and the Ground will be Shaking" New location on 10 plus acres Lots of pit/spectator parking New Clay Track Big payout class 2 Sleds at the same time Track Patrol Sleds Classes, Payout and rules to follow!! Will update soon Check our website for updates and directions: [www.riverfallsffaalumni.org] Thanks River Falls FFA Alumni Questions Call: Ryan 715 821 7676 Pete 715 821 7800 |
Classes
|
Farm Stock Non Turbo
4500 4 mph 45 Factory rated horsepower Max Tire 15.5x38 5500 4 mph 55 Factory rated horsepower Max Tire 15.5x38 7500 5 mph 75 Factory rated horsepower Max Tire 18.4x38 9000 5 mph 100 Factory rated horsepower Max Tire 18.4x38 11000 6 mph Farm Stock Turbo 10000 8 mph 11000 8 mph 12500 8 mph 14000 8 mph Improved Farm Stock (7 mph) 4500 5500 6500 Light Open 6500 7300 Heavy Open 7500 8500 9500 Hot Farm (2.8” x 3” Turbo) 11000 11500 Pro Farm (3x3 Turbo) 10500 11000 Diesel Trucks 8500 Street Stock Diesel 8000 Improved Stock Diesel (2.5 Turbo) 8000 Open Diesel |
Pictures of New Location Under Construction
|
Registered: 06/14/2016 Posts: 52 |
River Falls Days Update:
Here is some pictures of the new location for the 2016 River Falls FFA Alumni Tractor Pull! The track is complete, the parking lot/pit area is still under construction. The track is close to 400 ft long and a 100ft wide! The project will be complete very soon...will update pictures once construction is done with the new location New Location Address: Located behind Total Excavating 141 State Road 35, River Falls, WI 54022 A huge Thank You to Total Excavating - Chris Kusilek for making this new location happen! Questions/Directions Call: Ryan 715 821 7676 Pete 715 821 7800 |
Payouts
|
Registered: 06/14/2016 Posts: 52 |
Payouts for the 2016 River Falls FFA Alumni Tractor Pull - July 9th
Farm Stock Non-Turbo 1st $50 2nd $40 3rd $30 4500 5500 7500 11000 9000 1st $200 2nd $40 3rd $30 Farm Stock Turbo 1st $50 2nd $40 3rd $30 10000 11000 12500 14000 Light Open 1st $300 2nd $200 3rd $150 4th $100 6500 7300 Heavy Open 1st $500 2nd $200 3rd $150 4th $100 7500 8500 9500 Light Improved Farm 1st $50 2nd $40 3rd $30 4500 5500 6500 Improved Farm 1st $125 2nd $100 3rd $75 4th $50 11000 11500 Pro Farm 1st $150 2nd $125 3rd $100 4th $50 10500 11000 Diesel Pickups 8500 Street 1st $100 2nd $75 3rd $50 4th $25 8000 Street Improved 1st $125 2nd $100 3rd $75 4th $50 8000 Open 1st $300 2nd $200 3rd $150 4th $100 |
Re: Pictures of New Location Under Construction
|
Registered: 06/14/2016 Posts: 52 |
River Falls Days Update:
Here is some updated pictures of the new location for the 2016 River Falls FFA Alumni Tractor Pull! New Location Address: Located behind Total Excavating 141 State Road 35, River Falls, WI 54022 A huge Thank You to Total Excavating - Chris Kusilek for making this new location happen! Questions/Directions Call: Ryan 715 821 7676 Pete 715 821 7800 |
Map and Directions
|
Registered: 06/14/2016 Posts: 52 |
Directions To Pull Site
Highway 65 North: On Highway 65 North take the River Falls Exit, Take a right at the Stop Sign and the next left on frontage road "Huppert Street" Highway 65 South: On Highway 65 South take a right on "Huppert Street" Main Street in River Falls: On Main Street drive until North Main Street turns into Highway 65, go over Highway 35 and take left on "Huppert Street" Highway 35 South: On Highway 35 South take the River Falls Exit, take a left at the Stop Sign. Go over Highway 35 and take left on "Huppert Street" Questions Call or Text: Ryan 715 821 7676 Pete 715 821 7800 |
Pics of Parking Lot
|
Registered: 06/14/2016 Posts: 52 |
Here is Parking Lot/Pit Parking |
Added Hobby Stock Classes: 5700/6200
|
Registered: 06/14/2016 Posts: 52 |
Due to the interest we will be adding 2 hobby stock classes: Classes will be 100% payback
Rules Below Hobby Stock 5,700/6,200 lb 1) All General Rules apply. 2) Maximum Tire size: 20.8 x 38. 3) Motor- OEM engine block and head. 4) Tractor must have OEM engine block, cylinder head, transmission, and rear-end casing. 5) Any carburetion is allowed on NA engine. No fuel injection. 6) No cubic inch limit on naturally aspirated engines. 7) Diesels limited to one injection pump not larger than a Bosch P-series non-turbo 8) Water injection allowed. 9) Only gas, diesel or alcohol allowed no duel fuels. 10) Must have a steel flywheel and pressure plate. 12) Wide front ends required starting season 2017 13) Maximum of 156 inch wheel base measured from the center of the rear axle. |
Parking Map
|
Registered: 06/14/2016 Posts: 52 |
Here is a map for parking |
Re: River Falls FFA Alumni Tractor Pull - July 9th 2016
|
Seen the flier. What's with the no ecno mods?? Would like the seen them able to pull in the 6500 open class |
Re: River Falls FFA Alumni Tractor Pull - July 9th 2016
|
rules
|
Rules got changed to diesel only. |
Re: River Falls FFA Alumni Tractor Pull - July 9th 2016
|
AnotherPuller!
|
Can someone explain to me why the 6500 and 7300 OPEN class is restricted to a 3.0 turbo size? Isn't open mean open? Please explain? |
Re: River Falls FFA Alumni Tractor Pull - July 9th 2016
|
Rmp
|
It's their rules look at all the dumb rules how many people are going to stay away |
Rules
|
Registered: 06/14/2016 Posts: 52 |
River Falls FFA Alumni July 9th 2016 Tractor Pull Rules
Tractor General Rules 1. Be a Professional. Must have tractor registered before class starts. No exceptions made. Can call ahead of time to get registered if your tractor is arriving late. 2. Pullers must be 18 years of age or older to participate. Minors must have parent or Guardian consent forms signed. No one under the age of 18 will pull outside the Farm Stock Classes. No one younger than 12 years of age will be allowed to pull. 3. All pulls will be made from drawbar. The hitch height must not exceed 20 inches. All pullers must furnish their own twisted clevis or a 3” hoop hole. Clevis must be fastened to the drawbar with a 3/4” or larger bolt and safety pin. 4. No weights hanging directly above the draw bar. Must have 12” opening for the hook-up to the sled. 5. One fuel type only. Alcohol maybe used as fuel in open classes only. 6. Pulling order will be determined randomly by draw. 7. Operator must remain seated and drive in a safe manner. 8. Tractors must operate in a safe manner at all times. No chain jerking or hot-rodding Allowed. 9. All tractors must be in neutral or park when being hooked or unhooked from sled.“Hands up” signal by the driver will be used to indicate this is being followed. 10. Tractor must remain within the boundaries of the track. Failure to do so will result in Disqualification. 11. Tractor must be occupied while it is running. 12. Loss of any weight or part of the tractor will be grounds for disqualification. 13. All pulls must start with a tight chain and be straight in-line with the sled. 14. All drivers pull at their own risk. River Falls FFA Alumni, Total Excavating and Deiss Storage shall not be held responsible for any accident, injuries or damage to equipment. 15. Class pulling order and drivers order will be posted. 16. Tractors will be stopped if front wheels are more than 24” off the ground. 17. All tractors must scale prior to hooking to sled, immediately prior to the start of your Class. 200lbs grace over printed class weight. Once weighed, you are staged. Leaving the staging area is not allowed. 18. NO BEER OR ALCOHOL TO BE CONSUMED FOR CONTESTENTS!!!! 19. Track officials have the right to move a puller to a different class. 20. The first puller has no option of a re-hook. Only chance to re-hook is if the sled has adjustments made to it. 21. In the speed limit classes, the puller has 100 feet to adjust his speed, after 100 feet any time of exceeding the speed will result in disqualification. 22. Violations of any rule shall constitute a disqualification. Arguing with judges will not be Tolerated, and will result in immediate disqualification. 23. ALL GENERAL RULES APPLY TO EVERY CLASS!!! 24. All JUDGES’ DECISIONS ARE FINAL!!! Failure to obey track officials will result in Disqualification and may lead to removal from event. General Safety Equipment (Required for Light Open, Heavy Open and Pro Farm Classes) 1. All tractors must be equipped with the following safety equipment: 2. Steel flywheel, SFI approved scatter blanket, wheelie bars with bumpers strong enough to support weight of tractor, fenders, kill switch, 2.5lb fire extinguisher, SFI approved roll cage, side shields and a second shutoff at the pump. Must have a spring-loaded throttle that returns to idle. Must have a 3 way dump valve a head of the injection pump operated by a cable. 3. SFI approved fire suit, helmet, gloves, shoes, and five-point harness required. 4. Electric fans are required. Stock engine driver fans are not allowed. 5. A signed driver statement required for flywheel. 6. Safety equipment and other components must be made available for inspection upon request of judges and upon protests. Farm Stock 4500 non-turbo 45 Factory rated horsepower (4 mph) Max Tire - 15.5x38 5500 non-turbo 55 Factory rated horsepower (4 mph) Max Tire – 15.5x38 7500 non-turbo 75 Factory rated horsepower (5 mph) Max Tire – 18.4x38 9000 non-turbo 100 Factory rated horsepower (5 mph) Max Tire – 18.4x38 11000 non- turbo 6 mph 10000 turbo 8 mph 11000 turbo 8 mph 12500 turbo 8 mph 14000 turbo 8 mph 1. ALL GENERAL RULES APPLY 2. Must have OEM block, fuel system, frames, hoods, drawbar, seats, grills, and front end. 3. Cut tires not allowed. 4. Tractors must have working hydraulics and PTO. 5. Water injection not allowed. 6. Fuel source must be factory to make and model. If it’s a diesel it’s still a diesel. 7. Add on turbo’s: Factory and M&W Turbo’s allowed in all turbo classes. Must be installed in a stock appearing manner. 8. Any tractor with a blower internal or external will pull in a turbo class 9. Turbo Tractors: all oil lines, exhaust systems and intake tubing must fit in a total stock manner and must be installed on tractor in order to compete. Stock air cleaner housings and correct plumbing required. Air filter elements not mandatory. 10. 2800 RPM maximum for Turbo Classes and factory stock RPM set by the Nebraska Test Book for Non Turbo Classes. If tractor is not listed, 2000 RPM will be used as a base Improved Farm Stock 4500 5500 6500 7 mph 1. General rules apply 2. Tractors must have a stock appearing block, frames, transmission, rear end, and axle housing for the manufactures make and model. Cast cylinder head and their replacements are to remain unchanged in outside appearance. No 7-bolt main blocks in Oliver’s, no 12-port heads, no 1600 series heads. Blocks are limited to one size up in series. No 800 Minneapolis Moline components. After market cast iron manifolds allowed. 3. Maximum tire size 18.4x38, top cut only. 4. Side shields allowed. Rear fenders and electric fan are recommended. Scatter shield, wheelie bars and kill switch required. 5. Can run over up to 20% over stock RPM’s. 6. Hitches max 20” height. No closer then 18” from the center of the rear axle drawbar hole 7. No down draft, tank or airplane carburetors unless originally factory equipment. John Deere lettered series tractors can have a duplex carburetor. 8. Not allowed to shift torque while pulling Light Open 6500 7300 1. ALL GENERAL RULES APPLY 2. ALL GENERAL SAFTEY EQUIPMENT REQUIRED 3. Engine block cannot be modified externally in anyway. Only one injection pump Intercoolers allowed. No nitrous allowed. Only one fuel allowed. Up to a P Pump allowed. Alcohol not allowed. 4. Restricted to a max 3x3 single turbo. 5. Max tire size of 24.5 x 32 allowed. Heavy Open 7500 8500 9500 1. ALL GENERAL RULES APPLY 2. ALL GENERAL SAFTEY EQUIPMENT REQUIRED 3. Engine block cannot be modified externally in anyway. Only one injection pump allowed. Intercoolers allowed. No nitrous allowed. Only one fuel allowed. Up to a P Pump allowed. Alcohol allowed. 4. Can use multiple turbos. Hot Farm 11000 11500 (Turbo Maximum of 2.8” inlet by 3” outlet) 1. ALL GENERAL RULES APPLY 2. Roll bar or roll cage is required. If your tractor has a roll cage, a 5-point harness is required, otherwise a seatbelt is adequate. 3. SFI approved helmet is required. 4. Steel flywheel and SFI approved scatter blanket required 5. Wheelie bars and a cable operated air shut off at the rear of the tractor mounted in the middle. 6. Must have side shields if running a belt-driven fan. An electric fan is preferred. 7. No Injection pumps larger then an A Pump unless a P Pump came installed as OEM. 8. No cut tires allowed. 20.8 x 38 MAXIMUM 9. 3800 RPM limit. 10. Water injection is allowed. 11. 466 Block. Factory intake and exhaust manifolds. Driveline, transmission, rear axle, frames, front axles and sheet metal must match model of manufacturer. 12. Must have working PTO or hydraulics. No Slots or slug Turbo. No inner or after coolers. Pro Farm 10500 11000 (Maximum 3x3 turbo) 1. ALL GENERAL RULES APPLY 2. No block larger then 540” Cubic Inch OEM to tractor 3. 466” Cubic Inch or less is allowed a max of a 3x3 turbo. Over 466” Cubic Inch max 2.8 x 3” Turbo. 4. Roll bar or roll cage is required. If your tractor has a roll cage, a 5-point harness is required, otherwise a seatbelt is adequate. 5. SFI approved helmet is required. 6. Steel flywheel and SFI approved scatter blanket required 7. Wheelie bars and a cable operated air shut off at the rear of the tractor mounted in the middle. 8. Must have side shields. An electric fan is required. 9. No larger then P Pumps Allowed 10. Cut tires allowed. 20.8 x 38 MAXIMUM 11. No RPM limit. 12. Water injection is allowed. 13. Driveline, transmission, rear axle, and sheet metal must match model of manufacturer. 14. No Slots or slug Turbo. No inner or after coolers. 15. Factory OEM Intake and Exhaust manifolds. Hobby Stock 5700 6200 1. All General Rules apply. 2. Maximum Tire size: 20.8 x 38. 3. Motor- OEM engine block and head. 4. Tractor must have OEM engine block, cylinder head, transmission, and rear-end casing. 5. Any carburetion is allowed on NA engine. 6. No cubic inch limit on naturally aspirated engines. 7. Diesels limited to one injection pump not larger than a Bosch P-series non-turbo 8. Water injection allowed. 9. Only gas, diesel or alcohol allowed no duel fuels. 10. Must have a steel flywheel and pressure plate. 11. Wide front ends required starting season 2017 12. Maximum of 156 inch wheel base measured from the center of the rear axle  TRUCK GENERAL RULES 1. Be professional. Must have truck registered before class starts. No exceptions made. Can call ahead of time to get registered if your truck is arriving late. 2. Pullers must be 18 years of age or older to participate. Minors must have parent or guardian consent forms signed. No one younger than 16 years of age will be allowed to pull. 3. Maximum height of hookup and pulling point cannot exceed 26” to hooking point. Hooking point must have 3” opening 4. No weight can extend more than 60” forward from the centerline of the front axle. (for classes that apply) 5. All trucks MUST have working brakes. 6. Drivers must wear a seat belt or restraint system. No passengers allowed. Failure to do so will result in disqualification. 7.Pulling order will be determined randomly by draw. 8. Operator must remain seated and drive in a safe manner. 9. Trucks must operate in a safe manner at all times. No chain jerking or hot-rodding allowed. 10. All trucks must be in neutral or park when being hooked or unhooked from sled. “Hands up” signal by the driver will be used to indicate this is being followed. 11. Truck must remain within the boundaries of the track. Failure to do so will result in disqualification. 12. Truck must be occupied while it is running, failure to do so will result in disqualification. 13. Loss of any weight, part of the truck or if the doors or hood open while pulling will be ground for disqualification. Becoming disconnected from the sled while pulling will result in disqualification. 14. All pulls must start with a tight chain and be straight in-line with the sled. 15. All drivers pull at their own risk. River Falls FFA Alumni nor Total Excavating shall be held responsible for any accident, injuries, or damage to equipment. 16. Class pulling order and drivers order will be posted. 17. All truck must scale prior to hooking to sled, immediately prior to the start of your class. 200LB grace over printed class weight. Once weighed, you are staged. Leaving the staging area is not allowed. Hitch height will be measured at weigh in. 18. NO BEER OR ALCOHOL TO BE CONSUMED FOR CONTESTENTS!!!! 19. Track officials have the right to move a puller to a different class. 20. The first puller has no option of a re-hook. Only chance to re-hook is if the sled has adjustments made to it. So make it count! 21. Violations of any rule shall constitute a disqualification. Arguing with judges will not be tolerated, and will result in immediate disqualification. 22. ALL GENERAL RULES APPLY, UNLESS CLASS SPECIFIC 23. ALL JUDGES’ DECISIONS ARE FINAL!!! Failure to obey track officials will result in disqualification and may lead to removal from event.  8000lb Open Diesel 1. All general rules apply, along with class specific rules. 2. Trucks are highly recommended to have a Fuel/air shut off and Driveshaft loops. 3. 35-18.00-15 Bar and Cut tires permitted. 4. A fire extinguisher system is permitted and highly recommended. 5. OEM Firewall is mandatory. 6. The complete OEM floor pan is mandatory. 7. The body must be OEM truck body. The body must retain full sheet metal, after-market hoods are permitted. The hood must be closed and securely latched while vehicle is hooked to the sled. 8. D.O.T. approved helmet required to be worn while pulling. 9. All open class trucks must have SFI approved bell housing on clutch, SFI approved shield on transmission body, SFI flex plate, SFI approved damper, SFI fire extinguisher mounted within reach of driver and SFI approved fire jacket. 8000lb 2.5/ Outlaw Diesel 1. General rules apply, along with class specific rules. 2. Trucks are highly recommended to have Fuel/air shut off and Driveshaft loops. 3. Must be Dot approved tire. Maximum height 35 inches. No studded tires or chains. No alterations to tires permitted. No bar or terra tires. No duals unless factory OEM equipped. 4. A fire extinguisher system is permitted and highly recommended. 5. The complete OEM floor pan is mandatory. 6. The body must be OEM truck body. The body must retain full sheet metal, after-market hoods are permitted. The hood must be closed and securely latched while vehicle is hooked to the sled 7. Unweighted OEM trucks i.e. crew cab long box trucks along with dual rear wheel trucks will be allowed to pull so long as no extra weight is added to truck. 8. No hanging weights allowed, bed of truck only. 9. Diesel fuel only, no injectables (nos, meth, propane). 10. No hood stacks. 11. Suspension stops/ blocks are allowed, along with use of air bags. 8500lb STOCK Diesel 1. General rules apply, along with class specific rules. 2. Must have hood, fenders, doors, windshield, rear window. 3. No hanging weights allowed, bed of truck only. 4. Diesel fuel only, no injectables (NOS, water/meth, propane). 5. No ladder bars, No track bars. 6. STOCK single turbocharger (unless factory equipped i.e. 6.4 Ford Powerstroke). 7. Use of a singe tuner is allowed. 8. No lift pumps allowed. 9. No Hood stacks. 10. Max tire height is D.O.T. approved 35” tire. 11. Air bags allowed but cannot be inflated. No suspension stops/ blocks. 12. Trucks must be street legal and registered. 13. After-market intake is permitted. 14. Stock Fuel system, no oversized injectors, cp3, HPOP. |
Re: River Falls FFA Alumni Tractor Pull - July 9th 2016
|
fine time
|
fine time to put dumb rules on here |
Answers To Posts
|
Registered: 06/14/2016 Posts: 52 |
Seen the flier. What's with the no ecno mods?? Would like the seen them able to pull in the 6500 open class
If you wanna pull in Open and come support our FFA that would be awesome! Can someone explain to me why the 6500 and 7300 OPEN class is restricted to a 3.0 turbo size? Isn't open mean open? Please explain? We had a lot of requests to have a Light Open Class with a 3x3 Turbo Limit...so we did a survey and there was a lot of feedback supporting this class so we chose to run a Light Open with 3x3 Turbo rule then we added a 7500 Heavy Open with no Turbo Limit. We will try it this year and if it don't work we will look to change it for next year Thanks Questions Call or Text: Ryan 715 821 7676 Pete 715 821 7800 |
Pictures of track
|
Registered: 06/14/2016 Posts: 52 |
Pictures of the track! |
Re: Pictures of track
|
Kevin H
|
Looks like a nice new facility for some good pulling action! |
Re: Answers To Posts
|
bs
|
Light Open, ha. Call it the Lubich Limited Class. |
Re: Answers To Posts
|
Another Puller!
|
It just seems pretty weird, why most clubs over in Wi. OPEN means just that, make weight, and safety, your good! I had planned on coming over from central Mn. to pull. I have pulled in River Falls before, but over 7500 lbs is to heavy, and I'm not coming that far for 1 hook. I go to Boyceville, Grantsburg, Baldwin, they are all the same, 6500 open and 7300 open! FUNNY DEAL!!! |
Re: Answers To Posts
|
Registered: 06/14/2016 Posts: 52 |
To respond to "BS" and "Another Puller"...if you have an issue with our rules or how we are running our pull please contact us directly vs going on a public forum and expressing your opinion. Please realize that this is the River Falls FFA Alumni pull which consists of over 30 members who all take time out of there personal life to put this event on..it takes a lot of hard work and dedication from our members to put this pull on. There is no classes or rules set up for any members as rules and classes our voted on per our membership. Only reason classes got changed was we did some asking around and we had a survey and based on the feedback we got we decided to try something different this year. If it doesn't work we will change things for next year. Again, remember that this is a River Falls FFA Alumni Pull and this is our big fund raiser for the year. All the proceeds from the pull go back to our students..for example last year we were able to give back $3500 in scholarships for the 2016 senior class. Our members do there best to put on a fun successful pull...no pull is perfect and never will be and without promoters that are willing to put pulls on there wouldn't be any pulls period. So to "BS" and "Another Puller" if you have a concern please contact me directly
Thanks Keith Gunderson - River Falls FFA President 715 684 9241 |
Start Time: 5pm
|
Registered: 06/14/2016 Posts: 52 |
Start time : 5pm |
Re: Start Time: 5pm
|
Thanks to all who worked at the pull and those who helped get it ready. Looked like a very good turn out. |
Re: Start Time: 5pm
|
FOOLISH PLEASURE II
|
I would like to extend a special thanks to Pete, Nuts, and the entire crew that put on the pull. The track was wonderful, and I thought held up very well for a new track. ALL AND ALL we had a good time, with good people! Thanks again!
FOOLISH PLEASURE II |
Thank You!
|
Registered: 06/14/2016 Posts: 52 |
The River Falls FFA Alumni would like to thank everyone that came to the River Falls Day Pull! Thank you fans, pullers, promoters, and sponsors!!!
A huge Thank You to Total Excavating - Chris Kusilek for making this new location happen! Chris did an awesome job with the site preparation and the track was awesome! There was a total of 232 hooks!!! We wanna extend a huge thanks to everyone for there patience on this new location. Being this was the first year at this location our FFA wasn't sure how the site layout would work. Our FFA learned a lot from last nights pull and we will make improvements for next year to make the pull even better! There will be way more parking, bleachers, port e poddies, bigger beer tent and better flow in and out of the pull location. We would like any feedback we can get to better help our FFA Alumni improve things for next years pull! Any feedback we can get would be greatly appreciated! For Pull Feedback Contact Below: Thanks!! Text Ryan: 715 821 7676 Keith: 715 684 9241 Email: rf.ffa.alumni@gmail.com Thanks again for all of the support! River Falls FFA Alumni Sponsors Total Excavating Value Implement Ag Star Minnesota Ag Group - Hastings Fuel Lift Kinni Sports and Power Mel's Steiner Plumbing Electric Heating Inc South Fork Cafe Winfield Solutions Darrel's Septic Service Barnes Trucking Devine Liquor Countryside Coop Deiss Storage Systems Dicks Hometown Liquor RCD Western Wisconsin Ag Supply First National Bank River Falls Stunzya Hanson Construction Kwik Trip Plumber Concrete River Falls State Bank Next Generation Auto Emmas Bar Xcel Energy Atlas Tractor Rowdy Redneck Autobody Earthworks Glass Express Reis Insurance Agency Ace Ethanol Advanced Auto Care Alpha Gamma Rho Fraternity Auto Value Bernard of River Falls BMO Harris Bank Border States C&J Builders Carquest Comfort Plus Insulation County Materials Delander Farms Dorwin Farms Foley United Freeman Drugs H&F Home Furnishings Harvest Fest Helmer Printing Hove Auto Body Dairy Queen Hub 70 Design and Print Jackelen Autobody Jerry's Towing Johnson Quality Plumbing Kinnic Veterinary KJ's Hogg Pen Bar & Grill Leith Insurance Agency Meadowood Tool O'Reilly Auto Parts Pechacek's General Contracting Phoenix Bar & Grill Reliance Electric Motors River Country Cooperative River Falls Mutual Insurance River Falls Tire River Valley Ford Security Financial Bank Smith Sales St Croix Lanes St Croix Tax Steel Town Swedes Service The Big Horn Thunder Country 95.7 Walk On Therapeutic Riding Programs Inc Westconsin Credit Union Ace Hardware Express Lube and Rental American Family Insurance - Jill Morrow |
Re: Thank You!
|
Paull
|
Thanks to all who helped.promoted,sponsored,volunteered,helped,drank beer,hooked,graded,watered,put on a great show and facility and brought food !!!!!!!!!!! Great price on food and then about 11:30 it was reduced,about 20 people getting "chops on a stick at 11:45. LOL Really good turn out and a big twin track, thanks again !!!! |
Re: Thank You!
|
well
|
I bet that there is 6 tractors less next year thanks pete he can not tell drives that they can not pull in a class and then tell them it ok that how cps went down the toilet. |
To "Well"
|
To "Mr. Well" if you got an issue with how our FFA Alumni ran our pull be a man and call me directly vs posting this on pulloff under a fake name. Pete and Nutzy had a brother pass away Saturday afternoon before the pull even started and they were good enough to still come to the pull and work with heavy hearts...I would like to see you come and help out at a pull the same day you lost a family member. There was no decisions that Pete made on any classes, rules or anything on Saturday...I was the one that made all the final decisions on Saturday along with our President Keith Gunderson. If you have an issue be a man and call me and keep the Lubich Family out of this. Your negative attitude is not welcome. Our pull was a great success Saturday night for our FFA Alumni. The new location worked out great and Chris Kusilek had the track awesome! We had 232 hooks and over 2500 people in attendance so overall the tractor pull was a positive event so there is no need to come on this pubic forum and try to steer the pot to make this event negative cause your feeling got hurt! So to you "Mr Well" man up and call me if you have a problem.
Ryan Joy 715 821 7676 |
Picture from Drone
|
Registered: 06/14/2016 Posts: 52 |
Picture from Drone |
My two cents
|
Justsoyaknow
|
Just wanted say my 2 cents got my ass kicked in heavy farm. . . . .BUT the food was great scale guys were friendly as long with the rest of security an staff an had a heck of a good time! Looking foward to next year! |
Results
|
Registered: 06/14/2016 Posts: 52 |
Results for 2016 River Falls FFA Alumni Pull
Thanks again for all of the Support!! |
Website Statistics
Global: Topics: 38,731, Posts: 229,864, Members: 3,332.
This forum: Topics: 37,086, Posts: 225,984.
Global: Topics: 38,731, Posts: 229,864, Members: 3,332.
This forum: Topics: 37,086, Posts: 225,984.
Our newest member WestonFarms