Page 1 of 6
Pages: 12345
Results 1 - 30 of 157
runs too fast, get a hyper belt drive setup and be done with it
by
m8888ja
-
Forum
if it is a p3000, you can machine the bearing plate down to fit the pilot hole in the block, your oring groove will be gone, but just use a small amount of sealer,,works fine
by
m8888ja
-
Forum
4102597505, proven power, high quality ,and many top runners
by
m8888ja
-
Forum
most people don't know that these pumps have a good rate of injection. because cam is turning crank speed, hence one reason for good power from stock pumps
by
m8888ja
-
Forum
your either still 180 off or pump problems,
by
m8888ja
-
Forum
text me about the pump you will need,,4102597505
by
m8888ja
-
Forum
I have proven pumps for sale, reground cam ,billet cam ,text or call,4102597505
by
m8888ja
-
Forum
i have calibrated many A pumps from various big name shops,and have never seen 1200 cc from a 13 mm setup. I actually just done scheids latested 13 mm A pump ,1120cc, these are calibrated on equipment that is certified every 12 months, so I feel very confident in the numbers.i have seen many pumps rated at such and such, but very few meet the mark,.... mike ricketts
by
m8888ja
-
Forum
what rpm? etc.
by
m8888ja
-
Forum
13 mm will flow more fuel in the same amount of crank rotation
by
m8888ja
-
Forum
faster rate of injection,,
by
m8888ja
-
Forum
any live streaming from gordyville?
by
m8888ja
-
Forum
having rebuilt these engines for over 40 years, blackstack is correct, those blocks need to be bored, honed, to fit oversize sleeves. I have seen many guys try the farmall "m", way to rebuild these engines with little success.most will break and then you have real issues.the sleeves need to be installed with controlled pressure, not a bfh and flat plate, spend your money to do it correct, and the
by
m8888ja
-
Forum
wanna sell that pump?
by
m8888ja
-
Forum
just what for pump is it?
by
m8888ja
-
Forum
I have just what you need,,check for sale page
by
m8888ja
-
Forum
give me a call or text, I may have what you need,,,4102597505
by
m8888ja
-
Forum
case turns cc
by
m8888ja
-
Forum
i.h. fan. we can setup the governor for any rpm you need..up to 4800
by
m8888ja
-
Forum
follow me, my pumps are dual feed,recommended psi is 100 to 120 psi, flows to 520, 530
by
m8888ja
-
Forum
2 words to describe parts in the pulling world ***** "pulling" and " greed" take it from there diesel puller
by
m8888ja
-
Forum
reground camshaft A pump =4710.00***billet camshaft with 25 mm drive end taper= 6270.00*** 13mm m100 ambac pump=2960.00
by
m8888ja
-
Forum
I have new build A pumps, 13 mm plunger,9 mm cam,900 cc,ready to ship, plenty of references. call or text 4102597505
by
m8888ja
-
Forum
I have a new build 13 mm pump,, 530 cc,,, 4102597505 call or text
by
m8888ja
-
Forum
have a turbonetics 3x3, bought new, only 4 pulls on it, billet comp. wheel,2ex hsgs, 128 and 115,, call or text,,4102597505
by
m8888ja
-
Forum
if you want high flow numbers, you have to machine the retraction land off
by
m8888ja
-
Forum
not a popular pump in the pulling world, I would be interested if it has a hub on it,
by
m8888ja
-
Forum
I have very heavy straight lines .120 i.d. 14X14 ,, 28.00 each .these are very nice injection lines 4102597505 call or text
by
m8888ja
-
Forum
are you using fuel from last season?
by
m8888ja
-
Forum
Page 1 of 6
Pages: 12345