Hopefully u have another section in the avaid for ur turbo? Even if u do a single 20gpm pump isn't enough for a prostock u need Two 20gpm pump sections for the engine and one 1" for the turbo and then ur fuel pump on the rear. Just trying to help dont want u to lose an engine bc of loss of oil. And u should be over 100psi of oil pressure going down the track.
by
Oliver with Cat 3208
-
Forum
Tractor should be done for this season. Not sure of his plans on GN or not but should see tractor out this season sometime. Lets hope it runs well as always. And gives everyone a run for there money.
by
Oliver with Cat 3208
-
Forum
No because it is an invitational pull.
by
Oliver with Cat 3208
-
Forum
Haslag steel makes them
by
Oliver with Cat 3208
-
Forum
As of BG this year they still had it. Just no time to work on it in there schedule. Since one of the boys went to college. And since there tractors blew up a couple time these past few years that takes extra time to put back together. I am sure they will have it back out when they can find some more time.
by
Oliver with Cat 3208
-
Forum
Thanks for ur opinion. And yeah we could just put a 4.1 charger on but most of are bottom ends won't hold up. With out some decent amount of work. I do like watching the super farms bc u get to see the tractor actually lug and not just spin the tires all the way down the track.
by
Oliver with Cat 3208
-
Forum
No Super Farms? One of the biggest classes and not on ur list? Not starting anything was just curious of ur opinion?
by
Oliver with Cat 3208
-
Forum
Well we have a region 2 SF hook tomorrow and I will ask around. I do know that we had 20+ in waseon region 2 pull. The thing is the GN points are over so now all those boys come play with us region 2 guys for the purse money. And I have 2 super farms and I am located in NW Ohio so. If u could text me and give me location and some details (or post on here) so I can ask around tomorrow that would b
by
Oliver with Cat 3208
-
Forum
Super farm would work that weekend.
by
Oliver with Cat 3208
-
Forum
Where and when is this pull bc I pull super farm and that would be a good class to have. We usually have 10 tractors compete all season long and with up to 25 when there is no GN pull that weekend.
by
Oliver with Cat 3208
-
Forum
I have a show me performance one and it uses one pin in the middle (looks like a T ) and has to have two cables attached to it (one on each top corner of the T) to hold it in place and if one of the cables gets pulled the pin comes out and door shuts works really well. I can send pics if u want or just look them up on facebook.
by
Oliver with Cat 3208
-
Forum
Well I need to launch at 6000 to carry the rpms down the track with the v8 it's not a inline so I need all the rpms off the line I can get to get it moving faster.
by
Oliver with Cat 3208
-
Forum
How many weights for a crower pedal clutch in a super farm? Looking to leave the line at 6000 and carry 3000 down the track? Right now I have 4 on each bolt. And it pushes back on the pedal at 4500rpms. Can't hold it down to get to 6000.
by
Oliver with Cat 3208
-
Forum
U need steal braided hose to hold the high psi and the methonal. We use steal braided on are super farms with just plain water and pump lube.
by
Oliver with Cat 3208
-
Forum
Need to adjust fuel and water both need more. Best to talk to ur dyno/engine builder. Or who ever u buy ur bio from.
by
Oliver with Cat 3208
-
Forum
Scales are always off. I weighed 9300 last week and then Friday I only weighed 9100 on both if my tractors.
by
Oliver with Cat 3208
-
Forum
Ntpa is only one chain out doors. Two chains indoors.
by
Oliver with Cat 3208
-
Forum
This is out of NTPA rule book: Maximum ground clearness is bottom of wheel rim not to exceed 4 inches with front tires in normal operating position.
by
Oliver with Cat 3208
-
Forum
Also make sure ur turbo drain pipe is not plugged or has a high spot causing slight restrictions if the turbo doesn't drain the oil easily it will push it out the exhaust seal. Had this problem on are big block cat.
by
Oliver with Cat 3208
-
Forum
We where using a 4 hole x .032 on a AC 426 with a roosa master and then used them on an A-pump. We where running a 4&8 mph class at 3200 rpms. But we have since switched to a cummins and have the injectors for sale for $450. If interested call or text Bill @ 419-722-492three.
by
Oliver with Cat 3208
-
Forum
Got a good 3x3 Columbus turbo that we ran on a 3208 at 3000 rpms just been rebuilt asking $1800shipped to ur door. Worked real well for us for mph class and when we ran open class. Call or text Bill 419-722-4923
by
Oliver with Cat 3208
-
Forum
I know that the aviad pumps have a built in preasure regulator. Not sure about ur gear pump but ur regulator should handle it ok.
by
Oliver with Cat 3208
-
Forum
We run 40gpm (two 20 gpm pumps) with 90-120 psi on both of are superfarms. We have aviad external pumps 4 stages two for engine one for turbo and one for fuel.
by
Oliver with Cat 3208
-
Forum
We've uses ross racing pistons before and they are a very good piston. May have to send them one to duplicate and then have the make it to ur specs if u want some cut offthe top or whatever. Make sure u get them coated so they can stand a higher temp.
by
Oliver with Cat 3208
-
Forum
Cenpeco 20w-50 been running it for years in prostock and superfarm motors.
by
Oliver with Cat 3208
-
Forum
It has the same rules as super farm for heads. And they are allowed in super farm so they are allowed in light pro stock. Hope this helps.
by
Oliver with Cat 3208
-
Forum
He wasn't chasing points but about fifteen years ago bad kitty 2 blew the engine up on saturday night in bowling Green ohio. We pulled the engine down and it scored a few cylinder walls. Easy fix right just put new liners in Wrong. Cats are parent bores (aka no liners) so we had to bore the engine out so we went and got a boring bar only no machine and did it right in the tractor with crank
by
Oliver with Cat 3208
-
Forum
Has to be open so we can use the brakes to steer going down the track. We needle them so they act like locked diffs and drive straight and so the brakes work easier.
by
Oliver with Cat 3208
-
Forum
This who u was looking for?
by
Oliver with Cat 3208
-
Forum
Yes I am building a Oliver 2255 with a cat 3208. Jumping up from hot farm. It should be ready by June 4th we are running ntpa region 2 we won't make all the hooks but the majority of them we will.
by
Oliver with Cat 3208
-
Forum