Try it yourself on the dyno then you will know!
by
jonesy
-
Forum
What's to talk about? Been running hotfarm for 6 years now and haven't seen anything unsafe tire related issues yet! You might see someone run too low tire pressure and see tire bounce, but can do that in any class
by
jonesy
-
Forum
NTPA / PPL hot farms are over 1500 now
by
jonesy
-
Forum
My money is on Chuck Schraders tractor ! Deere 4960 wasn't painted yet don't know if it is now or not..... Tough tractor, Travis Smith no slouch either.
by
jonesy
-
Forum
Big rods are way to go, install good bolts, balance them and run em.
by
jonesy
-
Forum
Not the power so much as the torque. I bent 2290 rods and would guess 1100 hp range back then
by
jonesy
-
Forum
I've seen a plain old rain cap work just as good as a 600 dollar guillotine, have to try on dyno
by
jonesy
-
Forum
Buy it from Haslaag
by
jonesy
-
Forum
Use both upper bearing halves and cross drill oil hole to the thrust bearing. I've done this for a few years and have great luck
by
jonesy
-
Forum
Just clean up the ports and spend the money on injectors and turbo
by
jonesy
-
Forum
Too many variables to say, injector depth, spray pattern, bowl design etc. safer to go down than up. Each set up is different. Save your money an invest in a dyno session, you'll be shocked how much you can learn in a day what would take all season to tune
by
jonesy
-
Forum
I wouldn't use anything bigger than an # 18 tip ( enderle) and have at least 1000 psi
by
jonesy
-
Forum
I have a Columbas 3x3.5 hx60 with 25 t6 exhaust and GMS upgraded cover
269-930-0607. 2,200
by
jonesy
-
Forum
I run an Avaid fuel pump( belt drive) , has built in adjustable regulator. 6 years now, no issues. Roughly 1,500 will get you a Simpson water system, you'll never buy another, buy the gear pump.
by
jonesy
-
Forum
Simpson Performance ( Max). 517-543-3467
by
jonesy
-
Forum
Yes, Karl is from Hartland.
by
jonesy
-
Forum
Have commander 1000, love it!
by
jonesy
-
Forum
How big of bore? 4.625 I run .030 on top, .025 second ( gap less)
by
jonesy
-
Forum
Should handle that, billet input shafts aren't that bad, give Karl Kaun a call, has them 262-719-9338
by
jonesy
-
Forum
Complete system on for sale page listed
by
jonesy
-
Forum
I remember Rich. The Williams brothers bought it from Rich and haven't seen them in years.
by
jonesy
-
Forum
Hacks had one back in the 70's and 80's, then switched over to pro in late 90s. With horrible milk prices they parked it
by
jonesy
-
Forum
Prayers to Don and family!
by
jonesy
-
Forum
I have a set of Case pistons that I took out of my hotfarm when I switched to billet if your interested.
by
jonesy
-
Forum
Make sure lifters are in good shape
by
jonesy
-
Forum
Wondering what degree the injector angle is on john deere, thought it was 20 degrees tipped out?
by
jonesy
-
Forum
I see a lot of Propullers showing up in that class. If you don't have a circumference rule, I would put the Propullers on
by
jonesy
-
Forum
I have been pulling with IPL in hotfarm class since 2015. It's a great group to pull with. What makes the hotfarm class great is color and close competition.as a a whole package deal, mods , diesel trucks and combo class, 10 mph farm ( is really taking off) , I don't know where you can get a better show for the buck! With 25 hotfarm hooks I'm to busy to chase them all, but see noth
by
jonesy
-
Forum
As a competitor, location, pay, track and how your treated by who is putting pull on
by
jonesy
-
Forum
Use the turbo intake manifold
by
jonesy
-
Forum