Page 1 of 1 Pages: 1
Results 1 - 8 of 8
--15.5-38 Firestone 151 uncut, approximately 80% tread, nice tires--$1750
--18.4-38 Firestone non-metric Radial on 9 bolt duals, 70% tread, would run as non cut or top cuts--$1800
--IH 06/66 tube frame rails, go from rear axle housing to weight bracket/tow loop, split at transmission housing as well--$3250
--22x38 9 bolt wheels, heavy centers, reinforcing rings around bolt pattern, appro
by
ffafarmer
-
For Sale
Plans have changed and its time to move some parts, clean out the shop.
IH tube frame, bolts to rear end axle housings and goes forward to front tow/lift point. Splits at transmission housing set up for 400 series IH.--$3500
IH D&R transmission, don't know much about it other than it was removed from a Lt Pro in place of a ProFab--$3250
806/1206 heavy 38" cast centers with axle cla
by
ffafarmer
-
For Sale
--unit was a backup generator for a hospital, bought for a hot rod moline project and plans have since changed. Was setup to run on natural gas, suspect it has low hours but didn't come with an hour meter. $3500
Located in Defiance, OH; call/text 419-4three8-568eight
by
ffafarmer
-
For Sale
--set of 16x38" 9 bolt wheels, ~12" offset, painted red centers, white outer rim. Can text pictures. Located in Defiance, OH $600
--15.5-38 Firestone 151 uncut tires, ~75-80%, great to run uncut or top cut--$1500
--806 parts, radiator, front casting, oil cooler, fast hitch, shifters, dash/steering pedestal, 38" heavy cast centers--call/text for info
---All parts located in Defiance,
by
ffafarmer
-
For Sale
All parts located in Defiance, OH. Arrangements can be made to get to NFMS or NATPA pulls.
--Ford 8000/8600/9000/9600 taper axle 9 bolt cast hubs--$800
--Ford 8000/8600/9000/9600 fiberglass fenders, great shape--$1500
--IH/Farmall 806 8 bolt front axle, comes with wet bolster, rear support, 10.00-16 4 rib tires (low tread), 8 bolt wheels, steering lines--$1000
--IH/Farmall 806 Fast h
by
ffafarmer
-
For Sale
Parting out an 806 Famall LP
--8 bolt hub wide front--$1000
--Farmall badges with side panels--$200
Hood has a dent in front of muffler, tin over fuel tank is straight. Has a fast hitch. Message about any other parts.
PTO, dual remotes, cast rear centers, trans, rearend are all gone. Parts located in Defiance, OH. Can bring to Shipshewana or Louisville. 419-438-5688
by
ffafarmer
-
For Sale
we have done both, I'm not sure I like the over the tire straps as they are hard on the steering components/tie rods. I think I like using a jack adapted to fit into the front tow/lift point to take some pressure off the suspension and then strap down. Other thing we were thinking of doing was having blocks for under the ski bars so the tractor was in the right place every time and wouldn&
by
ffafarmer
-
Forum
I have done it, you need to cut about 3/4" square out of the bolster for the oil pan to clear. However, mine already had a modified damper on it when i got the engine so i didn't have any problems there. I still have my stock bolster here in NW Ohio if you want it instead of cutting your's apart.
by
ffafarmer
-
Forum