Where is the best place to buy a scatter blanket for a jd 4430 quad range tractor? Does anyone on here have a used one they want to sell?
by
4010 puller
-
Forum
Looks like 18.5". Bolt holes are 5/8" in rear and 3/4" for front, I have distance measurements for mounting bolts if needed. These measurements are from late 4840 block which should be same as 7.6 liter.
by
4010 puller
-
Forum
Isn't one of these tractors the one that grenaded an engine at national farm machinery show in 2005 or 2006?
by
4010 puller
-
Forum
I thought I read somewhere where the 4 spider setup would fit in 4230/4320 and up rear ends as direct bolt in but not sure if any were needled from factory
by
4010 puller
-
Forum
What kind of pressure should a guy feed to turned up Stanadyne rotary injection pump on a 310 Waukesha? Is a holly blue or red electric pump good to use or something different?
Where is best place to buy 5 gallon aluminum/stainless fuel tank?
by
4010 puller
-
Forum
What kind is yours? As jd diesel said, my stock style 4 disk is pretty well in or out, no slipping. Maybe I'm not making enough power yet out of the 404.
by
4010 puller
-
Forum
You can modify your stock clutch to make it a 4 disk, possibly 5.if looking for Sfi approved call atlas or Joe bush ag repair, rursch sells them too for around $4500.
by
4010 puller
-
Forum
What is the price on one of your pumps?
by
4010 puller
-
Forum
Possibly Wimer or fair valley, I would definitely get a bigger one from the get go, 10 mm probably will not be big enough, go with 11,12, or 13 mm
by
4010 puller
-
Forum
Ok, those late jd ones are about twice as heavy as the ones I had in mine, just switched them over to the heavier jd ones and put 3 cast hold downs on instead of the single aluminum ones.
by
4010 puller
-
Forum
I was just wondering what you guys are running for heavier valve springs on a jd 55 series head for 3000 rpm. Anyone know how heavy they should be or have any part numbers for any heavy ones?
Also, are stock pushrods and rocker arms and shaft adequate with the roll pin between head and rocker shaft?
Thanks
by
4010 puller
-
Forum
You can put 4 3/4" bore pistons/sleeves in an 8.1 and make it a 540 ci, what is your cubic inch limit?
by
4010 puller
-
Forum
Looks like there was an accident in New Jersey a few dsys ago too killing a young man, www.nj.com. Search for farm accident. Sounds as if had adjusted injection pump and it possibly ran away. There was a fb post on it this morning
by
4010 puller
-
Forum
Pretty close to 350 cc
by
4010 puller
-
Forum
Which main bearings do you get to put the 8.1L crank in a 466 block? Will the bearings need honed/resized for the crank to have the right oil clearances? Or will the block need work for the 8.1L bearings to fit?
by
4010 puller
-
Forum
What kind of class/setup are you running? In this case why would copper be a better choice than a regular headgasket with rings cut out and sleeves cut? Only reason I ask is ive heard copper gaskets are hard to seal up and leak water into cylinders. I had a jd 730 that had sat a few years, went to start it and it blew water everywhere, it got a stock gasket put back on it.
by
4010 puller
-
Forum
Ok so maybe a 8820 combine engine, 8430/8440 tractor engine, which those may be a hard find to get the bolt pattern I need. May be easier just to redo frame rails and use bigger bolt hole engine.
by
4010 puller
-
Forum
Ok thanks I didn't realize engine differences between 8820 and 8820 titan 2. 8430/8630 tractor blocks may possibly work too but there are none of those around here
by
4010 puller
-
Forum
Ok I think the 8820 and 4840 tractor blocks are the same, I think they both have the big bolt pattern
by
4010 puller
-
Forum
Hey guys do u know off hand which is the best application to get an engine out of that's p series injection pump to bolt into 4230/4430 directly without reworking frame rails?
by
4010 puller
-
Forum
4430 has valves in the pan? What do u mean by that
by
4010 puller
-
Forum
Hey guys:
When installing a 8.1 L in a 4430 do you use the dampener on engine or a 4430 style? Will the hydraulic pump drive rubbers screw right into the 8.1L dampener and be right length for hydraulic pump to hook up?
How about the oil filter housing on the 8.1, can you remove it and install a 4430 style horizontal style? That filter housing and filter are right in the way of the injectio
by
4010 puller
-
Forum
Hi guys, haven't spoke with anyone that's used mets machine shop. They are reasonably close and I was wanting some machine work done on a 466 Deere, just wondering how their work is, thanks!
by
4010 puller
-
Forum
I would say s300, part #177281, 2.6x2.8 with 91 exhaust housing. I think summit and jegs carry them but I would check with a guy on here that goes by injpumped. Several farm stocks around here are running them and they seem to do well.
by
4010 puller
-
Forum
May try Forrester farm equipment in Pennsylvania
by
4010 puller
-
Forum
Is the class you mention the bunker hill classic pro farm class or another? I didn't know of a 466 ci 3x3 turbo open rpm class either
by
4010 puller
-
Forum
Want to install p pump on 7.6L with s300 borg warner turbo
by
4010 puller
-
Forum
Ok thanks I've got a 13mm p pump off of a 4840 that's been modified. I wanted to put it on the 7.6L combine engine
by
4010 puller
-
Forum
Ok thank you
by
4010 puller
-
Forum
0402196700 is the other number on tag above the jd number
by
4010 puller
-
Forum