Cubic inch and turbo size still makes a big difference
by
4010 puller
-
Forum
That makes 505ci, 4.875" bore with stock stroke makes 531 ci
by
4010 puller
-
Forum
Maybe an s300
by
4010 puller
-
Forum
There are many different sized s300's, either make rules on a stock size s300 or have to buy a box charger through your organization. Not all 3lm turbos are the same size either. Stock is 2.3x2.7, you can get them 2.7x3 or 3x3. Sounds like you may need a tech committee in your area.
by
4010 puller
-
Forum
Where is the best place to pick up a set of Deere 55 series low ring pistons for a 466?
by
4010 puller
-
Forum
Americanfarmpullers.com and there is also Glenford lions club tractor pulls
by
4010 puller
-
Forum
Good videos!
by
4010 puller
-
Forum
8.1 with aftermarket 4 3/4 sleeves and custom billet pistons makes 540 ci
by
4010 puller
-
Forum
What's wrong with using the whole 8.1 liter natural gas version?
by
4010 puller
-
Forum
Looks like singer sled rental and on the mark pulling sled are both in ohio
by
4010 puller
-
Forum
How many tractors usually run in that 466 pro farm class? Is mn the only state running it?
As for this hot farm class, ppl has been running it for years with these rules and seem to have good results! Ostpa should consider a class like this too
by
4010 puller
-
Forum
Yea worth less than $1500
by
4010 puller
-
Forum
Should run pretty healthy. Which turbo are you going to run? I'm not sure that your 440 cc A pump is going to be big enough
by
4010 puller
-
Forum
I agree not worth adapting pumps, Its not worth changing stock engine for 404 a pump block.4440/4640 crank drive oil pump engine would be nice conversion or 6620/7720 combine engine.
by
4010 puller
-
Forum
Which is the best turbo to run on 466 Deere 3k rpm in a box charger? S400, gt42, holset hx 50-60? Which exhaust housing would a guy need?
by
4010 puller
-
Forum
What is pricing on that oil josh? I've heard brad penn or Schaffer may be better than Cenpeco.
by
4010 puller
-
Forum
Are you running the 4020 narrow block with pencil injectors or the old style 4010 block with the big injectors?
by
4010 puller
-
Forum
What's everyone running for a fuel supply pump? I've currently got a 10mm a pump but going to be running 13 mm p pump. I'm running a sprayer pump now that worked good but it's starting to not keep up at 350 cc. I know fass makes some electric pumps what else is out there? Are guys still running the tuthill pump off the front of the injection pump? Who is selling those setups?
by
4010 puller
-
Forum
Where is best place to get 6 new 466 sleeves with grooves cut for fire rings and head gasket all as one package deal?
by
4010 puller
-
Forum
Not sure that you can put direct injection head on indirect injection engine. They have two different head gaskets, I believe they made a 310 indirect and direct injection engine and 310 indirect was in 1800 tractors
by
4010 puller
-
Forum
So the s200 could be comparable to a 3lm-33? What kind of power are the 3lm-33's capable of? I think they are 2.3x2.5"
by
4010 puller
-
Forum
What is your engine setup and weight class? Open speed or speed limit? Rpms?
by
4010 puller
-
Forum
S200 is quite a bit smaller than 3lm. Basically the s300 replaced the 3lm466. Many different sizes of s300/3lm are available.
by
4010 puller
-
Forum
Riverside has them, not sure of anyone else
by
4010 puller
-
Forum
Who is making jd 8.1 re usable rod bolts? Where is best place to get them? Thanks
by
4010 puller
-
Forum
Hi guys, how many of you are still running a 404 in farmstock or 3000 rpm classes? How big of a turbo are you running and do you have any trouble keeping it spooled up? I suppose in the early days some had used the 404 with more than one turbo in the superstock division? Just wondered how much power I could make out of a 404 4430 engine in a 4010
Thanks
by
4010 puller
-
Forum
Wanting to remove oil cooler from 310 turbo diesel to clear steering shaft in 88. Looks like inside at block there are three ports, one farthest foreword is a oil pressure hole that fed factory oil filter. My question is the rear two that went thru heat exchanger, can they be blocked off or do they need tied together so engine gets proper oil flow? I don't have a manual that shows flow path
by
4010 puller
-
Forum
I haven't seen Charlie Ross tractor pull in several years, didn't know he was still pulling it?
by
4010 puller
-
Forum
The Pump Doctor : 740-877-9000
by
4010 puller
-
Forum
That probably wouldn't work too well, too much lag. You could try a 3lm-33 but may have to do some custom work for water manifold and exhaust. If you go with borg warner s200 or s300 they have the v band outlet which would make exhaust routing much nicer. Is your engine stock?
by
4010 puller
-
Forum