6.67, 5.28,4.625 5.11 .3.5
by
llss puller
-
Forum
i can make them from copper 859 544 2981
by
llss puller
-
Forum
I may have one. I'll check tomorrow
by
llss puller
-
Forum
I make them straight and l shaped
by
llss puller
-
Forum
Silver Creek Fabrication has hats and discs . Aluminum or steel 859 544 2981
by
llss puller
-
Forum
I made one using a stock gear and machining out the center and then machining a new center as described above . your local machine shop should be able to do that easily.Jolliff diesel may have some
by
llss puller
-
Forum
bolt on or v band
by
llss puller
-
Forum
Cornett in Somerset Ky did mine 2 seasons no problems . I cut my own counter weights and they put them on . They also destroked it.
by
llss puller
-
Forum
Depends more on amount of fuel ,RPMs,timing,cam, head flow,than cubic inch . I have run 32 housing on hx60 ,470ci for several years. Tried 27 but exhaust pressure was too high, exploded compressor with 27 housing. Best to have data aquisition computer and compare pressures. Start with big housing and go smaller. Pressures need to be close to same from exhaust to boost within 20 psi
by
llss puller
-
Forum
Thats how I made mine also, but its blue. Shouldn't be any problem finding the parts for IH. I think Columbus Diesel has them on their website . I know they did at one time.
by
llss puller
-
Forum
aluminum hats and rotors $750 859 986 7076 email kmhammons@windstream.net
by
llss puller
-
Forum
throttle handle and bracket $75 + shipping straight or l shaped 859 544 2981
by
llss puller
-
Forum
I sell throttle handles with mounting plate one shown in photo is straight , I also have a L shaped one. cable can be supplied also along with other needed connectors.
by
llss puller
-
Forum
859 544 2981
by
llss puller
-
Forum
I got an email from him also about some parts I wanted. For a Ford. When the spelling wasn't right and the phone # didn't match I didn't even give it a second thought.
by
llss puller
-
Forum
Diesels at 479ci and 3x3 turbo won't be competive at all . Maybe with 3.6 turbo or with 3x4 and intercooler. At least a 3x4 will put them within 20 feet. Maybe
by
llss puller
-
Forum
Most vane pumps have a sae mounting which will bolt up to the power steering pump location. just adapt a stock power steering gear to the pump
by
llss puller
-
Forum
when and where for the truck auction?
by
llss puller
-
Forum
what rpm are you trying to leave at. I think you need more fuel. I had a s4 turbo once with 132 housing, I could lite it at 4000 rpm easy.I had 800cc fuel and 45 cc water /15 sec. What compression ratio.
by
llss puller
-
Forum
mine is 160-180 degrees depending on how long I warm it up # of seconds of the run
by
llss puller
-
Forum
looks like the crank is hour glassed shaped.more clearance in center than on edges.
by
llss puller
-
Forum
pull is now cancled, per Battle Of Bluegrass website
by
llss puller
-
Forum
Most builders/parts suppliers have them or can get them . You will need a taper lock hub also. Total cost about $850. Riverside, GMS, Kenny's pulling parts to name a few
by
llss puller
-
Forum
I have used a RPM Performance data logger on a diesel LLSS for 5 years . no problems and have added other sensors to it easily.
by
llss puller
-
Forum
Silver Creek Fabrication, any thickness 859 544 2981
by
llss puller
-
Forum
This is what I use
by
llss puller
-
Forum
Use misting or fogger nozzels available from mcmaster carr. They have a chart for those nozzels . chuck up a pump in a drill press or Mill and plumb it up with a nozzel and pressure gauge ,do some expermenting with different types of nozzels and pressures. Hold a pipe the same size as your crossover pipe near the nozzel . you will be surprized at the difference in nozzels
by
llss puller
-
Forum
On the inlet side of the pump I use a filter with a stainless steel mesh screen such as you would find on a crop sprayer . Then each nozzel has its own built in filter to prevent clogging.
by
llss puller
-
Forum
Biodiesel at 2% works better for lube
by
llss puller
-
Forum