Page 1 of 2
Pages: 12
Results 1 - 30 of 31
Looking for front tires that are 4 rib and no taller than 28”. I’m terrible with front tire sizes and have 7.5L-15 currently, which fit on my frame. They are 3 rib and I want 4 rib. Just need pointed in the right direction for the tire and rim size. Thanks.
by
RTK
-
Forum
If I recall correctly the C2 shaft acts as the damper. It's the hollow shaft that acts as the damper either C1 or C2. Pretty sure it's C2
by
RTK
-
Forum
Contact Brendan for any questions 765-226-0810
by
RTK
-
Forum
The crankshaft has some end play but very little. I haven't measured it but I'd say it's within spec
by
RTK
-
Forum
P3000 pump
by
RTK
-
Forum
I'm not familiar with anything in the oil pump being brass
by
RTK
-
Forum
There's no shaft play in the turbo. And I just checked every rocker arm. Thrust bearings looked fine.
by
RTK
-
Forum
I have found brass shavings in the oil of my IH dt466. Found 3 little chips and the rest is just small flakes. I have checked every rod and main bearing, cam bushings, wrist pin bushings and rocker arm bushings and they are all fine, no chunks out of any of them. I have checked every place I know to check. Am I missing any place where they could have come from? Had engine completely apart this pa
by
RTK
-
Forum
I bought a steering motor from surplus center to use on my IH 1066 for closed hydraulic steering system and was wanting to see how some others mounted it and made a shaft for a removable steering wheel. Link is the motor I bought. Thanks.
by
RTK
-
Forum
Did you use the 5 port steering pumps?
by
RTK
-
Forum
And these work pretty slick to make your own adjustable tie rods.
by
RTK
-
Forum
This cylinder should work.
by
RTK
-
Forum
will you still run your MCV for power steering?
by
RTK
-
Forum
I was going to put the pump on a switch and only run it when I need to
by
RTK
-
Forum
I have searched and haven't found much on someone using a snow plow pump plumbed into a 4 port steering hand pump. I was wondering if you got a snow plow pump that would work with a double acting cylinder. I know some pumps are pressure one direction and gravity the other. I have seen tractors with an electric over hydraulic steering but haven't looked to see how they have plumbed it. I
by
RTK
-
Forum
I'm glad I'm not the only one. I think this year it was all luck.
by
RTK
-
Forum
Don't disagree with you, but I just help with the pull so I'll give them the idea and see what they say.
by
RTK
-
Forum
Call 317-833-2616 for any questions with directions.
by
RTK
-
Forum
Shot me a text or call
by
RTK
-
Forum
I have shims that I took out. If interested 317-833-2616
by
RTK
-
Forum
That what I was thinking too. It has to pivot somewhere
by
RTK
-
Forum
What do you mean by sway link?
by
RTK
-
Forum
Ok thanks.
by
RTK
-
Forum
removing mcv pump and will have no live power, so I wont have power brakes. without going to disc brakes can I still use the stock brakes and run a line from where pressure oil comes into brakes at, to a reservoir? so there will be oil coming into the brake assembly but wont be pressurized. im not sure if the oil supply to the brakes has to be pressure oil or if oil from a reservoir would work. t
by
RTK
-
Forum
It definitely needs to.
by
RTK
-
Forum
Message me please.
by
RTK
-
Forum
what size rotary pump? how much flow?
by
RTK
-
Forum
I'm starting to build a mild hot farm tractor that I bought. It's a 1066 with a dt466 in it and I'm wondering where I should start to try and get around 6-700 hp. It has a 300cc rotary pump with 5x.022 injectors .093 lines. 3lm turbo truck Pistons that have been cut and a different cam, I have a picture of the cam spec sheet. I'm deleting the ta and putting in stepper gears bu
by
RTK
-
Forum
Page 1 of 2
Pages: 12