Page 1 of 2
Pages: 12
Results 1 - 30 of 34
The factory liners arent very strong to start with. Go with a good liner like powerbore for 4 3/4
by
Srxboy
-
Forum
Go with a 6" stroke, block will need light clearancing and some on camshaft but best gain per dollar. just that puts you at 600 cubes. Then it you go to a 4 3/4 piston with a good liner you dont need any boring done in the block that combination yields 640 cubes. perfect setup for 3-3500 rpm. You can run open rpm but will need a billet crank for that.
by
Srxboy
-
Forum
With no speed limit and no rpm limit why have a farm and hot farm class? cut tires allowed in hot farm?
by
Srxboy
-
Forum
What are your improved farm rules? Speed limit?
by
Srxboy
-
Forum
Will the tractor still be able to be used around the farm? Dad just wants to have fun in a farm stock class but be able to use it if he needs.
by
Srxboy
-
Forum
How do I modify the stock clutch to make it a 4 disk?
by
Srxboy
-
Forum
Who makes a pulling clutch for a jd 4230? Will be used in a farm class with a 3lm or s300. Tractor is an 8 speed
by
Srxboy
-
Forum
Any chance of rescheduling?
by
Srxboy
-
Forum
Also curious about rain, What is your pulling order going to be? Will be leaving around 9:30
by
Srxboy
-
Forum
anyone know what tractor classes shell lake and jump river have?
by
Srxboy
-
Forum
karl at atlas tractor does it
by
Srxboy
-
Forum
Quoteeagle
get a manifold off of a 451 . they are smaller internaly. I searched the junkyard for a good one that is sealed real good. cam timing should be at 95 or 96 depending on your centerline. case does not like a tight housing. I would recommend a 115 in place of 101. also use a 2090 0r 2290 head or case industrial head as they use 45 degree valves instead of 30 degree valves. to make a goo
by
Srxboy
-
Forum
Has anyone ever foamed the rear end on a 70 series case? Not sure the best way to go about it.
by
Srxboy
-
Forum
How much you asking for it? Feel free to pm me with info.
by
Srxboy
-
Forum
Did these sytle boost valves work pretty good?
by
Srxboy
-
Forum
I used the fass 150 pump. Has a built in adjustable fuel pressure regulator and feeds my 700cc A pump just fine.
by
Srxboy
-
Forum
he contacted me a few days ago from my wanted add for a stroked crank. Same bs about not being able to provide pics. Said he was a broker for the seller. Scam true and threw, his texts were poorly written and english wasnt good.
by
Srxboy
-
Forum
Im running 3000-3500 depending where I pull. I am currently at 504 but considering going to 550 or even 585.
by
Srxboy
-
Forum
No I normally pull in 7th but thats in 11500 class. If I lost 1100lbs that would bring me down to 8800lbs with driver. I still have pto and hydraulics but no rockshaft so I could potentialy get down to that 8500 mark, then I'm sure I would be in road gear for the lighter classes
by
Srxboy
-
Forum
I pull an 1175 and currently weigh 9900lbs. I picked up a parts 970 with an 8 speed rear and was wounding how much weight would I lose by switching my 1175 rear for the 970? One person told me I could lose close to 1200lbs but I dont see the plantaries adding that much weight. Niether setup will have cast centers. Trying to decide if its worth the work of switching it out and the money of buying
by
Srxboy
-
Forum
what mph pace do you run on sun?
by
Srxboy
-
Forum
I would lean towards something else. Without know what application and how deep the relief cuts were you might see a difference of .5 in your compression ratio. This shouldn't make a noticable difference pulling, you may notice it starting however.
by
Srxboy
-
Forum
I have an 1175 case I'm finishing up to pull in hot farm, I was told i would need to put screws threw the rim into the beads of the tire. How many screws do I need in each bead and what kind of screws are people using? Tractor is around that 7-800 hp mark with 20.8x38 radials uncut. Thanks
by
Srxboy
-
Forum
Its nice to have a complete WI pulling schedule at on one site, Great job!
by
Srxboy
-
Forum
I want to make my 1175 into a tilt hood. Anyone have any pics of the hinges they use and how they supported the hood? Thanks
by
Srxboy
-
Forum
Where is everybody getting fire rings for case pullers? Freshing up my 504 and getting it fire ringed but my machinest want me to bring in the rings and I want to be able to easily order more if I need in the future. Thanks
by
Srxboy
-
Forum
Yes there is. The cover is very hard to find and can be expensive. I got mine off a 730. How did you get yours down that low with rockshaft and pto still on it?
by
Srxboy
-
Forum
I'm in the process of building an 1175, what do you all have stripped off of it? What is the tractors current weight?
by
Srxboy
-
Forum
How do you get 570cc's from a 10mm A pump?
by
Srxboy
-
Forum
Quotedgcasepuller
stock 504 heads have very big ports with lots of swirl. they need to be ported in order to get flow for bigger cubes. if the cubes are smaller the ports should be tightened up
For a 3000rpm 504 what do you reccommend?
by
Srxboy
-
Forum
Page 1 of 2
Pages: 12