Page 2 of 5
Pages: 12345
Results 31 - 60 of 148
Had a drain in each valve cover. I would groove both sides or make them deap so all the oil dumps on the cam. The more lube the better.
by
BM
-
Forum
I only did one side and heads filled up with oil so I got the otber side done and had drains just in case.
by
BM
-
Forum
The rear end housing, use the Comfort King housing, 150lbs heavier than the 400/800.
by
BM
-
Forum
Won't hold, I wrecked an 800.
by
BM
-
Forum
What Rear end?
by
BM
-
Forum
Never been in a 70 series , but did a early 30 series and a Comfort King. Great stuff foam in a can 2" at a time so it can dry. Also have used some 2" foam insulation to take up bigger spaces. Have a lightened CK rear to sell with some foaming done.
by
BM
-
Forum
I have a custom manifold off a Cummins that moves the turbo out front of engine.
by
BM
-
Forum
In the pan is ok. I would say no more than 300 watt each. I had a 1000 watt and it would burn the oil. I changed to pads on the outside. I run a 300 what on my turbo oil tank.
by
BM
-
Forum
LLSS in on the application for NTPA for 2017. WTPA added the class in 2016.
by
BM
-
Forum
I'm not worried about the teeth, It's the oil getting in between the shafts and gears that spin on the shafts.
by
BM
-
Forum
Anyone use Lucas Oil?
by
BM
-
Forum
So the 80w90 will be fine That I run?
by
BM
-
Forum
Have not had gear failure, looking for a light wt oil to run, to get to the shafts where the gears spin on, bull pinions and Case range gears. Going to do some winter pulling and looking for a thinner oil to get to the shafts. 90wt has worked in the summer, not so sure when its colder out.
by
BM
-
Forum
I ran a couple quarts of Lucus as well. Heard of guys running ATF.
by
BM
-
Forum
What's everybody using for lube. Was using gear lube, want something thinner to work good in colder Wheather also, a synthetic maybe. Its in a non pressure lube rear.
by
BM
-
Forum
So I would assume it would fit in a 12v.
by
BM
-
Forum
Does the 6.7 crank have the same rod and mains as the 5.9?
by
BM
-
Forum
Hate to drag this back up, anyone heard from him, he was going to get ahold of me a week and a half ago so I could send him a check for a cage. Now not answering emails or phone. He said he was real sick 2 weeks ago, is he ok?
by
BM
-
Forum
300 watts work good. I had a 1000watt and it would burn the oil. Then went to the stick on heaters.
by
BM
-
Forum
Where is the best place to get a bearing kit for a HX60?
by
BM
-
Forum
I would assume putting the rims together on the tire and lots of silicon. Instead of putting the tire on the rim when they're together.
by
BM
-
Forum
Going to mount a set of tires and wondering if there are any tricks or what's the best procedure?
by
BM
-
Forum
Looking for a battery disconnect and a kill switch for an alcohol tractor, NTPA legal. Where do most guys get them?
by
BM
-
Forum
Contact info for Jason?
by
BM
-
Forum
Where is the best place to get a cage kit from, 2 bar mild steel so I can put a base on it and MIG weld it?
by
BM
-
Forum
Got them, Thanks for the email
by
BM
-
Forum
Any chance you could post it different, I don't have Office on my computer.
by
BM
-
Forum
You can't use the link bars, you need to use the ones with the knobs so they don't turn. Put a groove on both sides on the lifter bore so the oil can get back down, or your valve covers will fill up.
by
BM
-
Forum
Extreme Studs
by
BM
-
Forum
What size axles did you go with? Wondering if 3" will hold.
by
BM
-
Forum
Page 2 of 5
Pages: 12345