Page 1 of 1 Pages: 1
Results 1 - 18 of 18
If I am not mistaken Todd this is the tractor of McMasters. I believe Fred still has it and his son ran it a few years ago.
by
michaelghenry
-
Pulling Forum
Most of my thoughts for the question of how do we attract more people to become, hopefully, an avid pulling fan reflect around the family and what a few others have mentioned.
Some thoughts if I were promoting a pull:
Since liability in the pits is an issue, bring a few of the pulling vehicles to the entrance so that the fans can get pictures and the kids can get into the seats. If I were as
by
michaelghenry
-
Pulling Forum
Miles,
Nice article...I know that there are several pullers that are also coaches who can relate.
by
michaelghenry
-
Pulling Forum
Anyone have pictures of the ATI setup for the IH 400 series? Was looking to attach a timing pulley to the ATI from Summit Racing.
by
michaelghenry
-
Pulling Forum
Spoke to Darrin and also Tom Urmson and Tim Engler. Pretty much boils down to if someone has one laying around from the 80's I guess.
by
michaelghenry
-
Pulling Forum
Does anyone have this setup laying around or know if anyone is still making them? Looking to put a 4 disc crower in and need to move back the cross shaft. Flywheel has stock ring gear and stock starter.
by
michaelghenry
-
Pulling Forum
Thanks. Wilwood customer service just told me that the Dynapro, 120-9695-SI, caliper that has the outboard, side inlet as well.
by
michaelghenry
-
Pulling Forum
Does the 6818 have the 1/8 inlet on both sides? I bought a set of caliper brackets but the 6817 calipers have the inlet on the housing side and the fitting hits the brake housing. Any pics of the 6818 setup?
by
michaelghenry
-
Pulling Forum
The whole list of posts on this topic has been interesting to read and to see the view points of different types of farmers, non-farmers, etc.
Agriculture is one of the rare examples of pure competition. There are a very large number of firms (according to the EPA website the number of farms stand at 2.2 million), the type of product is standardized (ie corn, soybeans, wheat), there is no con
by
michaelghenry
-
Pulling Forum
383331R1 - bottom freeze plugs
380174R1 - 3.510 size freeze plug (LH)
380173R1 - 3.762 size freeze plug (RH)
Might be what you are looking for.
by
michaelghenry
-
Pulling Forum
Looking for who makes rings for damper hub like the picture attached.
by
michaelghenry
-
Pulling Forum
When putting the thermocouple sensor in the exhaust of an IH 66 manifold, do you put it in approx. 2 - 2 1/2" and then tighten to compress the fitting (see attached picture) and leave the other part of the thermcouple stick out? The other thermocouple I had previously seen was originally only about 2 1/2" long but this new one is 5" long.
If I compress only 1/2 of the thermocouple will it eff
by
michaelghenry
-
Pulling Forum
Where is a good place to buy a turbo blanket for a T08? Saw T3/T4's on eBay.
Thanks.
by
michaelghenry
-
Pulling Forum
Thanks for posting the pictures....that is the first time I have seen a picture of Walton's D-21 in over 15 years.
by
michaelghenry
-
Pulling Forum
email me at michaelghenry@yahoo.com
I may have what you are looking for.
by
michaelghenry
-
Pulling Forum
You need to contact Art (System Accessories) who works with Shurflo at 877.917.1199 - this is for the Shurflo pump you are looking for. They put a new tag on the pump over the stock tag #, that is why it doesn't show on their website. They put a different diaphragm in for diesel fuel applications if I remember correctly.
by
michaelghenry
-
Pulling Forum
