Page 1 of 3
Pages: 123
Results 1 - 30 of 71
Call jegs or summit. Mustang II rack and pinion. Then you'll need non-power steering tie rod ends from them or AutoZone can order them. I have it on a 9000# tractor. Works good
by
Buckeyecrewcab
-
Forum
I sell the shutoff cables. Ready to go with 2" free hanging loop. Also build guillotines and have hose sets to mount. Cables run $75. 513-571-4532
by
Buckeyecrewcab
-
Forum
I have a brand new set of the plugs part number 383331R1 if needed. $20 513-571-4532
by
Buckeyecrewcab
-
Forum
Guy that has screen name of pullmx had them. Sorry I don't have his number.
by
Buckeyecrewcab
-
Forum
Hello all, wondering what starter everyone uses on a sbjd 466 with a marine intake. Will a high torque starter fit without intake modification? Thanks in advance.
by
Buckeyecrewcab
-
Forum
Go to Deere and have them order a 4850 charger from A&I. Direct bolt on. A lot better then the stock 4440 charger.
by
Buckeyecrewcab
-
Forum
Dengler Tractor 513-423-4000 can help you with anything on that 2 cyl you need. thanks
by
Buckeyecrewcab
-
Forum
I can steer you in the right direction. call me when you get a chance. 513-571-4532
by
Buckeyecrewcab
-
Forum
Check out Dctpa.com for all rules on antique classes.
by
Buckeyecrewcab
-
Forum
Castner has really nice pressed braided lines made up. Nice guys to deal with
by
Buckeyecrewcab
-
Forum
What class are you building for? True hot farm or too hot to farm? As in a hot farm stock
by
Buckeyecrewcab
-
Forum
On a sbjd, if you look from the very end of the shaft, there will be a round insert pressed in and a set pin also to keep the round from slipping. You'll be able to see a defined line on the very end. I would think a bbjd is the same...
by
Buckeyecrewcab
-
Forum
Any builder has them/ can get them. Or any drag racing shop has them. Or Alkydiggers.com
by
Buckeyecrewcab
-
Forum
What tractor is this turbo on? JD, IH, ford? What model, etc
by
Buckeyecrewcab
-
Forum
Seeing what switch works best to do a neutral start safety setup on a 4430 rear end with a 3 SPD installed in it. Have seen the switches with the roller ball plunger in them, just don't know what they fit. I appreciate any info given. Thanks again!
by
Buckeyecrewcab
-
Forum
Fastenal has or can order any length you need up through grade 21. Castner is a good guy to go through on parts too. Also extreme stud in rushville Indiana makes head studs, etc.
by
Buckeyecrewcab
-
Forum
No nerve at all pullwatcher. But I'll make ya a deal. I want you to buy 200 of those, store them, machine them, buy all the supplies to put them together correctly, assemble them, and ship them to me no cost, while having a satisfaction guarantee on them, but I want you to do all that for $15 each, OK? So if you can do that I'll take 200 right now! Because that would save me an enormous
by
Buckeyecrewcab
-
Forum
Still waiting on a phone call pullwatcher. If you can trash talk on your keyboard, then you can trash talk just as easy on the phone. Thanks again.
by
Buckeyecrewcab
-
Forum
Well pullwatcher, if doesn't look like you know your math skills very well at all. And if you have any beef with myself or product that I sell please call me and let me know what the problem is. Thanks!
by
Buckeyecrewcab
-
Forum
I make all sizes of guillotines and velocity stacks including 2.5" call me and I can explain in more detail. 513-571-4532 thanks again
by
Buckeyecrewcab
-
Forum
I can have hardened for $500/set. place does good work. 513-571-4532
by
Buckeyecrewcab
-
Forum
no problem at all. i have a 12" crower 4 disc and it fills the housing pretty well. i cut the housing toward the front so the adjusting hole is even with the pan flange. obviously leave the thick flange on the housing though. i have enough room to get to the stands and nuts that way. i run 9000 class and haven't had any strength issues coming down hard a few times
by
Buckeyecrewcab
-
Forum
rustydib,
I had the same question. I air arced an opening from stock access hole toward front of pan flange. opening is roughly 12'' deep x 14'' across. i then made a new access cover using the original cover and adding a piece onto that. hope this helps. with anything more than a single disc clutch, i believe you'll need more of an opening to adjust.
by
Buckeyecrewcab
-
Forum
I can have hardened for you. sets usually run in the $500 range. that's hardening only, no machine work. then just take to your machine shop and have rods reworked. 513-571-4532
by
Buckeyecrewcab
-
Forum
i'm a deere guy but theyre pretty for sure. the 1st tractor brought ok money. the last 2 i think were on the weak side for a big auction. couldnt restore them like they were for those prices!
by
Buckeyecrewcab
-
Forum
Bill L,
i sell them ready to go. 15' HD shutoff cables are $75 shipped to your door. 513-571-4532 thanks
by
Buckeyecrewcab
-
Forum
David,
you need to use VITON o rings. mcmaster carr has them. tried all the above before i went with the viton orings. the better setup although more money is what jd 5020 said. the stock brake pucks take alot of pumping to get pressure before each run. hope this helps
also put the new cardboard backup rings in that fit beside the orings. get those from deere
by
Buckeyecrewcab
-
Forum
Me,
where are you located at?
by
Buckeyecrewcab
-
Forum
connect the 2 wires from the sensor to the 2 flat spade terminals on your cord. don't connect the ground spade
by
Buckeyecrewcab
-
Forum
if you're talking of the sensor that is mounted by your front dampner then mine came from scheid. its an isspro sensor. ran around the $55 range. hope that helps you out.
by
Buckeyecrewcab
-
Forum
Page 1 of 3
Pages: 123