easiest way is to take out the delivery valve assy. and use a 1/2 inch wooden dowel. if it wont go in the plunger bore ,it is most likely a 10mm. possibly an 11 mm. if it goes in the bore with a bit of play its most likely a 13mm .
by
m8888ja
-
Forum
need help locating inner tie rod ends for the steering cylinder from surplus center. thanks ,,they are 3/4-16 thread
by
m8888ja
-
Forum
pobar - 9 years ago
is the pobar system an enclosed system or does it need a pump.? thanks
by
m8888ja
-
Forum
very good ..nice to deal with
by
m8888ja
-
Forum
looking for Justin mannings phone number.. have parts done for him,,but no number
by
m8888ja
-
Forum
ANY deviation from the 2014 rules should include turbos that have had the compressor cover ground down to meet the 7.750 rule. another way of bending the rulebook..
by
m8888ja
-
Forum
so the interstate tractors cant run the 24.5x32 topcut tires?have to use 20.8 38?
by
m8888ja
-
Forum
looking for opinions on intercoolers.?good ones, not so good ones. what is preferred.etc. thanks
by
m8888ja
-
Forum
probably not a 9 mm.not many 9 mm heads left. most use 10 mm.the stop plate and nose cam angle along with droop screw determine the amount of fuel injected.
by
m8888ja
-
Forum
air brakes = CDL. period all 50 states.go ahead ,try it
by
m8888ja
-
Forum
466 engine, water inj. intercooler,open rpm, 2.4 turbo, how much fuel? and what kind of timing, give me ideas guys,,,a pump
by
m8888ja
-
Forum
the reason why Jason walked out and pointed him to forward off the track instead of immedietly rehooked is because he knew something was wrong, ! gave him a chance to fix it, why have rules..?
by
m8888ja
-
Forum
again, there is no clear cut reason that he should have been allowed to pull.jsut look at the video cory and curt and danny and Jason,who waled out to point him off the track.watch the video and then say it was fair .that case should be in the finals.and I am a green guy, not oarange
by
m8888ja
-
Forum
as a spectator.i want to know why blue force was allowed to be in the finals. the tractor shut down well past the 75 ft, line, he did not make an attempt to shut it down and coast past the line. I feel that the case tractor should be in the finals. not blue force.lets play by the rules !! you get ONE attempt .period, unless the test puller, which he was not !!! another sneaky trick? why did th
by
m8888ja
-
Forum
hey barnstormer, pm me with your new number
by
m8888ja
-
Forum
depends on turbo,i have built pumps that run very well on 466 but they require lots of water for cooling if you run a good turbo,some use a 2.8 precision , the bigger the cu. in. the leaner it will be
by
m8888ja
-
Forum
looking for input -opinions on riverside engines. parts ,,cylinder head work,?
by
m8888ja
-
Forum
astounding performance rotary pump service. 410-259-7505
by
m8888ja
-
Forum
I can build you a high flow pump, fast delivery and very dependable.adjustable fuel load fuel,up to 505 cc,,email,m8888ja@yahoo.com
by
m8888ja
-
Forum
have always had nothing but good parts from allied, they have what I feel is the best ta out there for pulling,,very helpful guys
by
m8888ja
-
Forum
just take out the cooler relief valve and plug the holes,,simple
by
m8888ja
-
Forum
you either get a good one or not so good, very expensive to say the least, pm me about a 13 mm pump
by
m8888ja
-
Forum
just take out the oil cooler relief valve and plug the oil cooler holes,,bingo,,easy as that
by
m8888ja
-
Forum
looking for a narrow front for 66 series ih,,, let message here on forum,thanks
by
m8888ja
-
Forum
better add the countershaft support bearing also,,it will bend,then you have a big mess on ur hands and you will be buying another 3rd gear set.. take heed my friend
by
m8888ja
-
Forum
anyone know how to get ahold of karl at atlas? been calling for 2 weeks,,no return calls ,anyone else have this issue? or does he have another number?
by
m8888ja
-
Forum
have the pump serviced,most likely a seized plunger.
by
m8888ja
-
Forum
j&m does build the type " A" pump. quick cam,and close flow, our model 100 has the quickest gov. built ,no surging and very smooth
by
m8888ja
-
Forum
wheels - 11 years ago
any vendor or anyone else bringing rims to keystone pull? looking for aluminum 24.5 rims,12 to 14 offset,,cash in hand,best price gets the cash
by
m8888ja
-
Forum
j&m tractor srv. inc. very reliable and flows to 480 cc. call mike 410-259-7505, since 1976
by
m8888ja
-
Forum