Page 1 of 1 Pages: 1
Results 1 - 25 of 25
What is "this road" in reference to?
by
jkloda
-
Forum
I love reading threads like these - apparently component chassis = class domination.
by
jkloda
-
Forum
If the center section looks like a 172, two ways to identify it are to either pull an axle to measure diameter and count splines, or pull the center out and get the part number off the ring gear.
by
jkloda
-
Forum
A fluid is a gas or a liquid.
Turbulent and laminar flows are ways to describe the flow of any fluid, regardless of viscosity or operating pressure.
by
jkloda
-
Forum
Somewhere between 2010 and 2015 the language was changed to 504 cubic inch limit without fuel specification. I don't have any insight on the why.
by
jkloda
-
Forum
The 2010 PPL rulebook listed diesels at 650 and alkies at 504 for the light class.
by
jkloda
-
Forum
I was scanning the super mod rules the other night related to permitted engines, and I see that marine and industrial engines are permitted (1 or 2 depending on club). Continuing down through the rules, the engine max bore spacing is limited to 5.00". What does this apply to? Allisons are permitted, but their BS is definitely over that limit. Seems to be fairly vague to me. Does anyone have any i
by
jkloda
-
Forum
I saw admission was $5 on the IH club's Facebook page. Is that the cost for admission for the pull also?
by
jkloda
-
Forum
QuotePuller ss
That recommendation was that the 505 methanol tractors run the same weight as the Diesels.
I thought they ran pretty well with the weights set up as they are now...
by
jkloda
-
Forum
Scott had one:
by
jkloda
-
Forum
The location of the feed holes in the bodies when dual and triple fed are improved.
by
jkloda
-
Forum
Does anyone know off-hand what the bore spacing is on the DT360?
Thanks.
by
jkloda
-
Forum
The 24v Cummins head (5.9/6.7) will marginally outflow the 12v head if both are "ported to the max". There are other factors with the 24v head that deter most people from using it over the 12v head - injector selection and valve spring selection to name a few.
by
jkloda
-
Forum
I made a plate to cover the thermostat hole and filled the head from the bottom side. That is how it was suggested to me by a friend that did one for his IH.
Hope that helps.
by
jkloda
-
Forum
That can be very misleading especially since some of the results are listed in hundredths of a foot. Does it vary with the sled that is used?
by
jkloda
-
Forum
SF - first place is 256.11 and second is 256.3? Are these results not listed in tenths of a foot?
by
jkloda
-
Forum
I wasn't there either, but Dave's new tractor is a DLSS.
by
jkloda
-
Forum
That was my thought, but I wanted to get some other opinions. I'd like to regear my 172, but that will involve purchasing another center section or complete axle (which I have found with a locker in it).
by
jkloda
-
Forum
Are lockers holding up in the rear of SMFWDs? Or are the options really only a welded carrier or spool?
by
jkloda
-
Forum
You'll have more to worry about if the thermocouple probe melts. Type K are the type typically used and they are good well over 2000°F.
by
jkloda
-
Forum
QuoteDougk20
I am looking to install a Data Logging System on my 210 AC Superfarm. I am looking for a system that allows for future expansion. I am want to keep cost reasonable, only installing the major sensors initially (6 EGT & 2 PSI). I would like to also send a signal to a AutoMeter Tach. Any feedback or recommendations would be a great help.
Thanks
Doug
I'd check out RPM data logge
by
jkloda
-
Forum
Quote5.9 cummins
i have recently purchased a 5.9cid cummins came out of a 89 pick up i want to make between 500 and 600 hp any one no of a good combo for this engine and what needs to be done to make this much power from a 5.9 do you need to fire ring or girdle it? I have a 12mm p pump and intercooler for the 4wd ramcharger im putting it in i want it to b streetable but have some smoke under the
by
jkloda
-
Forum
I am poking around for a mechanical pump for water injection. I stumbled across a variety of Vickers vane pumps but have not been able to locate any that are rated over 4500 RPM. I would like to drive this via a gear at 1:1 to the crank, as that would be easy to set up.
Are there any other pumps/pump families I should look at? Or should I scrap the idea and run it off a pulley at <1:1?
by
jkloda
-
Forum
Do you run an intercooler and are you running port water now?
by
jkloda
-
Forum
I was looking for an SQHD for quite some time, but I was not coming up with much that didn't cost two arms and a leg. This H172 sort of fell into my lap.
I've done some more reading, and I'm leaning toward just narrowing the stock housing and putting the lightweight parts in it.
by
jkloda
-
Forum