Page 1 of 2
Pages: 12
Results 1 - 30 of 37
Would not work...boost is merely a measure of resistance. The better the air flow the less boost with the same cubic inch and turbo setup.
by
ole king cole
-
Forum
sure will, what is the best time tomorrow
by
ole king cole
-
Forum
Thanks, knew there were several options just was not sure what they were charging for labor. Needing to make some extra money and have a gentleman willing to let me do some machine work for him. I personally like the needles and flat needle bearings everywhere but to each his own I know some guys have made brass work fine. Thanks again for the info. Darrin
by
ole king cole
-
Forum
Can anyone tell me what they charge to put needle bearings in the differential of a 4010 and 4020 rear end. Also will put needles in the planetarties.. I have a customer but has been a few years since I have done any. Thanks, Darrin Cole
by
ole king cole
-
Forum
If memory is correct you want the R26010
by
ole king cole
-
Forum
Several suppliers and builders on here. you use the stock ring gear and pinion shaft. replace the top shaft and counter shaft. mine is several years old but I had to machine the front of the case and both quill assembles are steel.
by
ole king cole
-
Forum
put a 3 speed in it. initial cost seems high but no more problems.
by
ole king cole
-
Forum
While you are at it you need to put needles on the sides of your planetary gears. Some on here will say it is not necessary but do it once and do it right.
by
ole king cole
-
Forum
Needing a thinner neck brace for a Christmas present. The one he has is 2 inches thick. if memory serves me correctly it is a RCS??? Any suggestions, I cannot find specs other that sfi anywhere. Thanks.
by
ole king cole
-
Forum
What roller lifters are they using in a sbjd?
by
ole king cole
-
Forum
36 is close to a 1.32 I think
by
ole king cole
-
Forum
do you know what the eight difference is between the two?
by
ole king cole
-
Forum
It helps all the way around. it will not take as much brake to guide it and also makes it go much straighter. Money well spent.
by
ole king cole
-
Forum
have you had needle bearings put in?
by
ole king cole
-
Forum
it has been several years ago, 3/8 hole probably 60 holes or so. i would not do it.
by
ole king cole
-
Forum
If you are running the stock wet brakes do not do it. i tried it once the holes shredded the pads and it was a heck of a mess to clean up.
by
ole king cole
-
Forum
I wondered the same thing years ago... Then i split one of the washers on the side of the planetary and ran it though the sun gear and broke the housing. I decided it did not matter why and put needles in. It made a world of difference, well worth it. Darrin
by
ole king cole
-
Forum
no, i truly was not aware of that, thanks.
by
ole king cole
-
Forum
What is the sfi spec for scatter blankets for ppl and outlaw?
by
ole king cole
-
Forum
Nothing against turbonetics, i just have several garrett 90s, 95s,74s,holset 60s and 80s. it would be cheaper on my end to bearing them than buy a new one.
by
ole king cole
-
Forum
I'll have to do some more digging, but lily bearing makes them. troulbe is they have minimum quantities and they are expensive
by
ole king cole
-
Forum
Has anyone tried to machine and fit ceramic thrust bearings in their existing turbos?
by
ole king cole
-
Forum
pt number R26010 if my memory is not faulty. never weighed any so do not know the difference, however it is significant.
by
ole king cole
-
Forum
Now I am on the correct page. I have found a metric tire that is supposed to cross ovewr to a 30.5X32 but is actually 31.5X32. Since metric sizes are not included in the rule books i assume i would have to remove 1/2 of rubber from the side of each lug to be legal?
by
ole king cole
-
Forum
about any machine shop should be able to do it, i just did my own. shaft is pretty hard and it takes some time, but not too bad.
by
ole king cole
-
Forum
do they make bigger exhaust husings than a 336? if so what sizes are available? Darrin
by
ole king cole
-
Forum
how many different exhaust housings do they make for a 4 LE and what sizes are they? Darrin
by
ole king cole
-
Forum
Will a 4020 ring gear bolt on a 4010 carrier? been too many years, i cannot remember.
by
ole king cole
-
Forum
doesn't take much. used one out of a pinto i think, electric fan and 12 volt water pump.
by
ole king cole
-
Forum
I am putting my super back together with some small changes. i just want to hook without having to completely rebuild. I'll pull with outlaws, bush and any of the open classes in whatever association. it is a matter of spending 5-7K verses 40-50K. should be able to make weight from 6000 and up. Do not have the time money or desire to pull NTPA. Nothing i have is set up to go down to 1 c
by
ole king cole
-
Forum
Page 1 of 2
Pages: 12